![](/images/new-backgrounds/1332485/33248521x1.webp)
OPERATION
WARNING:
Do not allow familiarity with tools to make you care- less. Remember that a careless fraction of a second is sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could re- sult in objects being thrown into your eyes, resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not recom- mended by the manufacturer of this tool. The use of at- tachments or accessories not recommended can result in serious personal injury.
APPLICATIONS
You may use this tool for the following purposes:
nCutting all types of wood products (lumber, plywood, paneling, composition board, and hard wood).
nCutting masonite and plastic.
nCutting drywall.
nCutting metals such as sheet steel, pipe, steel rods, aluminum, brass, and copper.
CAUTION:
To prevent damage to the battery pack, remove the battery pack from the charger immediately if no LED comes on. Return the battery pack and charger to your nearest service center for checking or replacing. Also, if you are removing the battery pack from the charger and no LEDs are on, return both the battery pack and the charger to your nearest service center. Do not insert another battery pack into the charger. A damaged charger may damage a battery pack.
LED FUNCTIONS OF CHARGER
LED WILL BE ON TO INDICATE STATUS OF CHARGER AND BATTERY PACK:
nRed LED on = Fast charging mode.
nGreen LED on = Fully charged and in maintenance charge mode.
nGreen LED on = When battery pack is inserted into charger, indicates hot battery pack or that battery pack is out of or below normal temperature range.
nYellow and Green LEDs on = Deeply discharged or defective battery pack.
nNo LED on = Defective charger or battery pack.
CHARGING THE BATTERY PACK
See Figures 3 - 4.
Battery packs for this tool have been shipped in a low
charge condition to prevent possible problems. Therefore, you should charge it until the green LED on the front of the charger comes on.
NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharg- ing) for them to become fully charged.
CHARGING A COOL BATTERY PACK
If battery pack is within normal temperature range, the red LED on charger will come on.
NOTE: If the charger does not charge the battery pack under normal circumstances, return both the battery pack and charger to your nearest Ryobi Authorized Service Center for electrical check.
nCharge the battery pack only with a recommended charger.
nMake sure the power supply is normal household voltage, 120 volts, 60 Hz, AC only.
nConnect the charger to the power supply.
nPlace the battery pack in the charger aligning raised rib on the battery pack with the groove in the charger.
nPress down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the charger.
nNormally the red LED on charger will come on. This indicates the charger is in fast charging mode.
nRed LED should remain on for approximately 1 hour then the green LED will come on. Green LED on indicates battery pack is fully charged and charger is in maintenance charge mode.
NOTE: The green LED will remain on until the battery pack is removed from the charger or charger is disconnected from the power supply.
nIf both yellow and green LEDs come on, this indi- cates a deeply discharged or defective battery pack. Allow the battery pack to remain in the charger for 15 to 30 minutes. When the battery pack reaches normal voltage range, the red LED should come on. If the red LED does not come on after 30 minutes, this may indicate a defective battery pack and should be replaced.
nAfter normal usage, a minimum of 1 hour of charging time is required to fully recharge battery pack.
nThe battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.
nDo not place the charger and battery pack in an area of extreme heat or cold. They will work best at normal room temperature.
NOTE: The charger and battery pack should be placed in a location where the temperature is more than 50°F but less than 100°F.
nWhen batteries become fully charged, unplug the charger from power supply and remove the battery pack.
11