TROUBLESHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORISED SERVICE DEALER.
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
| ||
|
|
|
|
|
| |
Engine will not start: | 1. No spark. | 1. | Check spark. Remove sparking plug. Reattach |
| ||
|
|
|
|
| the sparking plug cap and lay sparking plug on |
|
|
|
|
|
| metal cylinder. Pull the starter rope and watch |
|
|
|
|
|
| for spark at sparking plug tip. If there is no |
|
|
| 2. | No fuel. |
| spark, repeat test with a new sparking plug. |
|
|
| 2. | Push primer bulb until bulb is full of fuel. If |
| ||
|
|
|
|
| bulb does not fill, primary fuel delivery system |
|
|
|
|
|
| is blocked. Contact a service dealer. If primer |
|
|
|
|
|
| bulb fills, engine may be flooded (see |
|
|
| 3. | Flooded engine. |
| next item). |
|
|
| 3. | Remove sparking plug, turn trimmer so |
| ||
|
|
|
|
| sparking plug hole is aimed at the ground. |
|
|
|
|
|
| Move choke lever to “RUN” and pull starter |
|
|
|
|
|
| cord 10 to 15 times. This will clear excess fuel |
|
|
|
|
|
| from engine. Clean and reinstall sparking plug. |
|
|
|
|
|
| Pull starter three times with choke lever at |
|
|
|
|
|
| “RUN”. If engine does not start, move choke |
|
|
|
|
|
| lever to “CHOKE” and repeat normal starting |
|
|
|
|
|
| procedure. If engine still fails to start, repeat |
|
|
| 4. | Starter rope pulls harder now than |
| procedure with a new sparking plug. |
|
|
| 4. | Contact a service dealer. |
| ||
|
|
| when new. |
|
|
|
|
|
|
|
| ||
Engine starts but will not | Carburettor requires adjustment. | Turn “H” needle anticlockwise 1/16 turn. If “L” |
| |||
accelerate: |
|
| low needle cannot be turned anticlockwise, do not |
| ||
|
|
|
| force plastic limiter caps. Contact a service |
| |
|
|
|
| dealer. See Figure 18. |
| |
|
|
|
| |||
Engine starts but will only | Carburettor requires adjustment. | Turn “H” needle anticlockwise 1/16 turn. If “H” |
| |||
run at high speed at half |
|
| high needle cannot be turned anticlockwise, do |
| ||
choke: |
|
| not force plastic limiter caps. Contact a service |
| ||
|
|
|
| dealer. See Figure 18. |
| |
|
|
|
|
|
| |
Engine does not reach full | 1. | Check oil fuel mixture. | 1. | Use fresh fuel and the correct |
| |
speed and emits excessive | 2. | Air filter dirty. | 2. | Clean the air filter. Refer to “Replacing and |
| |
smoke: | 3. | Carburettor requires adjustment. |
| Cleaning the Air Filter ” earlier in this manual. |
| |
|
| 3. | Turn “H” needle clockwise 1/16 - 1/8 turn. |
| ||
|
|
|
|
| See Figure 18. |
|
|
|
|
| |||
Engine starts, runs, and | Carburettor requires adjustment. | Turn idle speed screw clockwise to increase |
| |||
accelerates but will not idle: |
|
| idle speed. |
| ||
|
|
|
|
|
| |
String will not advance: | 1. | String welded to itself. | 1. | Lubricate with silicone spray. |
| |
|
| 2. | Not enough string on spool. | 2. | Install more string. Refer to “String Replace- |
|
|
| 3. | String worn too short. |
| ment” earlier in this manual. |
|
|
| 3. | Pull strings while alternately pressing down on |
| ||
|
| 4. | String tangled on spool. |
| and releasing spool retainer. |
|
|
| 4. | Remove string from spool and rewind. Refer to |
| ||
|
| 5. | Engine speed too slow. |
| “String Replacement” earlier in this manual. |
|
|
| 5. | Advance string at full throttle. |
| ||
|
|
|
|
|
|
|
15
