Manuals / Samson / Home Audio / Speaker

Samson EX10, EX20 Specifications, Frequency Response all models, Sensitivity, Crossover Frequency

Models: EX10 EX30 EX20

1 17

Download 17 pages 60.11 Kb

Page 17

Specifications

Power Rating: (@ 8Ω	):
EX10		250 Watts Program; 400 Watts Max. Peak
EX20, EX30		160 Watts LF; 40 Watts HF
Frequency Response: (all models)		60 Hz – 15 kHz ± 3 dB
Sensitivity:
EX10		97 dB SPL @ 1W/1m
Crossover Frequency:
EX10		2.3 kHz (12 dB Per Octave)
EX20, EX30	2.3 kHz (24 dB Per Octave Linkwitz-Riley Constant Phase)
LF Driver: (all models)		12" heavy-duty driver ,
		2.5" voice coil (Kapton Former),
		50 oz. barium ferrite magnet
HF Driver: (all models)		1" compression driver
Stereo Mixer Section: (EX30 only)
Inputs		2 Mic/Line XLR/TRS,
		1 Stereo Line w/Mic TRS/RCA/XLR
Outputs		+4 Balanced XLR
Frequency Response		10 Hz - 50 kHz
Crosstalk		70 dB @ 1 kHz
Equalization Frequencies		100 Hz (Low), 10 kHz (High)
Effects		DSP Reverb with 6 Presets
Mounting: (all models)		Integral 1 3/8" Pole Mount Receptacle,
		Fly Points
Dimensions: (all models)		14 5/8 in. (w) x 17 3/8 (d) x 21 1/4 (h)
		371 mm (w) x 441 (d) x 539 (h)
Weight:
EX10		28.5 lbs • 12.9 kg
EX20		42.0 lbs • 19.0 kg
EX30		45.0 lbs • 20.4 kg

17

Image 17

Samson EX10 Specifications, Frequency Response all models, Sensitivity, Crossover Frequency, Dimensions all models, Weight

Contents

EX10 EX20 EX30 Expedition Accessories Specifications Table of Contents Introduction System FeaturesEX10 EX20 EX30 Positioning and Mounting InstructionsIntroduction System Features which allows any Expedition enclosure to System FeaturesInterconnecting the EX10 Speakon WiringExpedition EX10 Guided TourExpedition EX10 Using two EX10s in mono A single mono signal bus or aux send is routed from a mixer to a power amplifier. One speaker output of the power amplifier is connected to either the EX10 1/4 input solid line or Speakon input dotted line, and a connection is made between either the 1/4 extension to a second EX10’s input solid line or between the Speakon extension to a second EX10’s Speakon input dotted lineGuided Tour Interconnecting the EX20Expedition EX20 Expedition EX20 Using two EX20s in mono A single mono signal bus or aux send is routed from a mixer to one EX20’s XLR input, and a connection is made between that EX20’s XLR output to a second EX10’s XLR inputGuided Tour Expedition EX30Expedition EX30 5 Insert sub connector - This 1/4 connector brings line-levelsignal in directly before the EX30 power amplifiers. It is normally used to return signal from an optional EX500 subwooferExpedition EX30 Interconnecting the EX30Expedition EX30 Using one EX30 and an EX20 stereo operation In this example, microphones are connected to the XLR mic inputs of channels 1 and 2 of an EX30, and a stereo keyboard is connected to the stereo 1/4 TRS connector of channel 3/4 of the EX30 using a Y-cord,with the tip carrying the left signal and the ring carrying the right signal. A connection is then made between the Right output of the EX30 to the XLR input of an EX20. IMPORTANT NOTE When using the EX30 with additional Expedition enclosures, always be sure to set the EX30 Mono/Stereo switch to “Stereo.”General Positioning Tips Positioning and Mounting InstructionsPole-Mounting Fly Mounting, Wall Mounting, and Ceiling MountingPositioning and Mounting Instructions Before fly-mounting, wall-mountingor ceiling-mountingthe Expedition, you must first install a Samson MP 1030 mounting bracket to the fly points, as shown in the illustrations on the rightSOFT EJECT Expedition AccessoriesGuided Tour TD30 Dimensions all models SpecificationsWeight Frequency Response all models