Samson PL2404 manual Guided Tour Rear Panel, Samson

Guided Tour - Rear Panel

1

2

3

				4									7
	PL 2404 24 CHANNEL PROGRAM STEREO / LINE MIXER													SAMSON
											2	0	-10	2	0	-10
					TRS		TRS	TRS INSERT		XLR		1			1
POWER					STEREO INPUT		BALANCED	UNBALANCED		BALANCED		3	−50	3		−50
					TIP = LEFT		TIP = HI	TIP = RETURN		3 = LO		+4			+4
					RING = RIGHT		RING = LO	RING = SEND		2 = HI
	ON		BUS OUTPUTS		SLEEVE = COM		SLEEVE = COM	SLEEVE = COM		1 = COM							8
											MIC 3			MIC 1
			UNBALANCED
				<75Ω+4dBu
	OFF		2	1	23	21	19	17	15	13	11	9	7	5	3	1
																LEFT / MONO
																	9
	AVIS:															RIGHT
	RISQUE DE CHOC ELECTRIQUE
FUSE	NE PAS OUVRIR				24	22	20	18	16	14	12	10	8	6	4	2
	DO NOT EXPOSE THIS EQUIPMENT		4	3
1A/250V
	TO RAIN OR MOISTURE							LINE INPUTS - BALANCED 10KΩ+4dBu
													4	3	2	1	10
	POWER															INSERT
	RATING 115V - 60 Hz 25W
	CAUTION	!	R	L
	RISK OF ELECTRIC SHOCK
	DO NOT OPEN			MAIN
			BALANCED <75Ω+4dBu		4	3	2	1	4	3	2	1	4	3	2	1
	~AC INPUT
	115V, 60Hz
	25W		R	L		BUS INSERTS				AUX RETURNS				AUX SENDS
			CONTROL ROOM		UNBALANCED <75Ω +4dBu					STEREO INPUTS				UNBALANCED <75Ω +4dBu
	S/N		BALANCED <75Ω+4dBu			MIXER LINKING				UNBALANCED 10KΩ+4dBu
			5	6			11				12			13

1:Power on-off switch - As you may have guessed, this is what you use to turn the PL 2404 on and off. To avoid potential damage to your speakers, turn the PL 2404 on before you turn on any connected power amps—and turn it off after the power amps are turned off.

2.Fuse - Contains a 1 amp, 250 volt fuse.

3.AC input - Connect the supplied standard 3-pin “EEC” plug here.

4:Bus out (1 - 4) - These unbalanced outputs allow you to route signal from each of the four discrete buses to external devices such as a multitrack digital or analog tape recorder. The signal is post-bus fader but pre-Main control. See the “Busing, Submixing, and Channel Muting” section in this manual for more information.

5:Main Out (L, R) - These are the PL 2404’s main outputs. In live performance applications, you’ll usually use these to connect the PL 2404 to a power amp and speakers; in recording applications, these will normally be connected to the inputs of a two-track recorder. The Main out jacks are electronically balanced, so you should use balanced three-conductor cabling and 1/4" TRS plugs wherever possible (unbalanced two-conductor plugs can also be inserted into these outputs, but you’ll get better signal quality and less outside noise and hum if you use balanced lines). See the “Connecting the PL 2404” section on page 10 for more information.

6:Control Room Out (L, R) - In recording applications, these will normally be connected to a power amplifier and loudspeakers. The Control Room out jacks are electronically balanced, so you should use balanced three-conductor cabling and 1/4" TRS plugs wherever possible (unbalanced two-conductor plugs can also be inserted into these outputs, but you’ll get better signal quality and less outside noise and hum if you use balanced lines). See the “Connecting the PL 2404” section on page 10 in this manual for more information.

8