Connecting the assembly cable, Power cable | Samsung AQV24PSBXSER

2. Fix the indoor unit.

Fixing the installation plate

2. Fix the indoor unit.

If you fix the indoor unit on a wall

(1) Fix the installation plate to the wall giving attention to the weight of the indoor unit.

• If you mount the plate to a concrete wall using plastic anchors, make sure that

gaps between the wall and the plate, created by projected anchor, is less than 20mm.

Plastic

Anchor

<20mm

Wall

If you fix the indoor unit on a window frame

(1)Determine the positions of the wooden uprights to be attached to the window frame.

(2)Attach the wooden uprights to the window frame giving attention to the weight of the indoor unit.

(3)Attach the installation plate to the wooden upright using tapping screws.

If you fix the indoor unit on a gypsum board

(1)Use stud finder to find out locations of the studs.

(2)Fix the plate hanger on two studs.

• Search for other spots if there are less than two studs, or the distance between the studs are different from the plate hanger.

•Fix the installation plate without inclining to one side.

•Make sure that a wall can withstand the weight of the product. If you install the product in a place where it is not

strong enough to withstand the product weight, the unit could fall and cause injury.

Connecting the assembly cable

If using a multi system, install as described in the installation manual supplied with the outdoor unit.

Cable specification

	Model	Power cable	Interconnection cable	Type GL



	AQV09/12PA	3G, 1.5mm² H07RN-F	4G, 1.5mm² H07RN-F	20A
	AQV09/12PB	3G, 2.5mm² H07RN-F	3G, 1.5mm² H07RN-F	20A
	AQV09/12PB	3G, 2.5mm² H07RN-F	2* 0.75mm² H05RN-F	20A
			2* 0.75mm² H05RN-F
	AQV18/24P	3G, 2.5mm² H07RN-F	3G, 1.5mm² H07RN-F	25A
	AQV18/24P	3G, 2.5mm² H07RN-F	2* 0.75mm² H05RN-F	25A
			2* 0.75mm² H05RN-F

• Connect the power cable to the auxiliary circuit breaker. If every pole fails to connect to

the power supply, it must be incorporated in a wire with a contact opening of ≥3mm.

Connecting the cable

Electrical work

(1)For electrical and earth works, comply with the‘technical standards of electrical installations’and the the wiring regulations’of the Electricity Enterprises Act.

(2)Tighten the terminal block screw to under 12kgf.cm.

(3)Precautions when connecting terminal blocks of the indoor unit

Before connecting, make sure the connecting part of the terminal socket is facing upwards.

			The terminal		There is no ring
	Upside down		The terminal		There is no ring
	Upside down		socketis damaged.		terminalto cover the wire.

28

Image 28

Samsung AQV24PSBXSER manual Connecting the assembly cable, Cable specification, Connecting the cable, Power cable, Model

Contents

Page Features of your new air conditioner Cool Summer OfferCost Efficient System Look for Everywhere Safety precautions USING PARTSImportant safety symbols and precautions FOR INSTALLATION FOR USING FOR POWER SUPPLYDo not pull the power cord, when unplugging the power plug Do not touch the power plug or the circuit breaker with wet hands FOR CLEANING Do not clean the inside of the air conditioner by yourselfDo not place objects or devices under the indoor unit Do not operate the appliance with wet hands Checking before use Operation rangesModel RJ Maintaining your air conditioner Power button Checking the name of the partsMain parts Display Checking the remote controller Remote controller buttonsRemote controller display Smart Saver On Timer Remote controller display Battery changing timeStoring the remote controller Turbo indicator Basic function AutoCool Heat button to adjust the temperature Press the button to turn on the air conditionerPress the button to set the operating mode Press the Adjusting the air flow direction Using the Turbo functionPress the Air swingbutton on the remote controller Press the Turbo button on the remote controller during Cool mode When the air conditioner is on and in cool/heat mode 1. Press the button on the remote controllermode Temperature and fan speed changes in mode Setting the On/Off timer Setting On timer Setting Off timer1. Press the On Timer/Off Timer button Additional options available in On timer mode Using the Smart Saver function If the air conditioner is onIf the air conditioner is off Combining On Timer and Off Timer Using the Quiet function Using the Auto Clean functionPress the Auto Clean button When the air conditioner is turned off When the air conditioner is turned on Cleaning the air conditioner Cleaning the indoor unitCleaning the outdoor unit heat exchanger Opening the panel Cleaning the air filter Removing the Air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated area Maintaining the air conditioner Periodical checks Troubleshooting PROBLEMSOLUTION not work at all Error is indicated Noise is generatedflow movement changes. It is normal the outdoor unit General information INSTALLATION PARTSIncluded Models Choosing the installation location Installing the unitPower supply line, fuse or circuit breaker Indoor unit Outdoor Unit When installing 1 outdoor unit When installing more than 1 outdoor unitSpace Requirements for Outdoor Unit Top view Accessories in the indoor unit case AccessoriesAccessories in the outdoor unit case Fixing the installation plate Optional accessoriesTools required for installation General Tools Tools for test operations Connecting the assembly cable Cable specificationConnecting the cable Power cable of the electrical contact during a wiring work Installing and connecting the assembly pipe of the indoor unit 10. Connect the grounding conductor to the grounding terminals11. Close the terminal board cover by tightening the screw carefully 2. Smooth the cut edges Purging the indoor unit Cutting or extending the pipe4. Cut off the remaining foam insulation 6. Pass the pipe through the hole in the wall 4. Put a flare nut slightly into the pipe and modify the flare Depth AOuter Diameter Outer Diameter D Installing and connecting the drain hose of the indoor unit Drain hose installation Installing and connecting the drain hose of the indoor unit Changing direction of the drain hose1. Detach the rubber cap with the plier 2. Detach the drain hose by pulling it and turning to the left InstallAA ing and connecting the drain hose of the outdoor unit Purging the connected pipes2. Connect a drain hose to the drain plug 3. Ensure that condensation draining is adequate gas service port as seen in the picture Adding RefrigerantIf you use a pipe longer than 5m If you use a pipe shorter than 5m Important information regulation regarding the refrigerant used Cylinder with siphon1. Please fill in with indelible ink 1975 PerfoAA rming the gas leak tests To check for gas leaks on the outdoor unitTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valves Outdoor unit installed on the wall by rack 6. Attach the pipe to the wall using clamps optionalFixinAA g the indoor unit in place Fixing the outdoor unit in place 1. Press the Power button and check the following 4. Press the Power button to stop the operationFinalAA Check and Trial Operation Check the followings The compression dimension should be and compress another two points in the same location5. Apply heat to the contraction tube to contract it 6. After tube contraction work is completed, wrap it with the Sub PCB installationoptional 1. Turn the power off and take off the front panel of the indoor unit2. Take off the Cover PCB 3. Attach the Sub PCB to the right side of the Panel-frame ENGLISH QUESTIONS OR COMMENTS? COUNTRYCALL EEE Yönetmeliğine Uygundur This EEE is compliant with RoHS user & installation manual Air Conditionerimagine the possibilities AQV07P Series AQV09P Series AQV12P Series AQV18P Series