•
Fasten the nib cover.
Below 20%
Red
80 ~20%
Violet
Above 80%
Blue
Battery level
Indicator light colour
1
• You cannot switch the indicator off while in pairing mode.
• The indicator light will always work when the device is turned on or off, when a call is received, in Pairing mode and when the battery is low.
Setting the vibration mode
You can set your device to vibrate when it is turned on or off and receives a call.
• Press and hold both the Talk button and Volume up button at the same time to set the vibration mode. Your device vibrates.
• Press and hold the Talk button and Volume up button at the same time again to cancel the vibration mode. The indicator light flashes red twice.
Press and hold both Volume buttons at the same time to turn the indicator light on or off.
S Pen
Spring
• Make sure the button of the S Pen aligns properly with the side button of your device.
• Spring and S Pen inside the device are not sold separately.
Turning the Bluetooth on or off
You can use the Bluetooth feature when the device is turned on.
• To turn on your device, press and hold the Talk button. The indicator light flashes blue 4 times.
• To turn off your device, press and hold the Talk button for 3 seconds. The indicator lights flashes blue and red then turns off.
Turning the device on for the first time, it will automatically enter pairing mode for about 3 minutes.
Turning the indicator light on or off
The status light is to show you the current status of your device, but if it bothers you at night, you can turn it off.
Press the S Pen into the device, aligning with the device’s side button.
1 When the spring falls out, press the spring into the device.
2
3
When the device battery is low
The device indicator light flashes red and you can hear beeps. If the device powers off during a call, the call will be automatically transferred to the phone.
Repeatedly charging and discharging of the device, over time will cause the battery performance to diminish. This is normal for all rechargeable batteries.
Assembling the device
If required, assemble the device as shown below.
2 Plug the travel adapter in to the wall socket. During charging, the indicator light will turn red. If charging does not begin, unplug the travel adapter and plug it in again.
3 When the device is fully charged, the red indicator light changes to blue. Unplug the travel adapter from the wall socket and the device.
Checking the battery level
To check the battery level, press and hold the Volume down button and the Talk button at the same time. Depending on the battery level, the indicator light flashes 5 times in one of the following colours:
Lift the cover of the charging socket with your fingernail and connect the travel adapter.
Charging the device
This device has a rechargeable internal battery which is non-removable. Make sure the device is fully charged before using it for the first time.
Use only Samsung-approved chargers. Unauthorised or Non-Samsung chargers could cause damage to the device or in extreme circumstances an explosion, it could also invalidate any warranty on the product.

HM5100

User manual

 

Printed in China

 

GH68-37401C Rev.1.1

www.samsung.com

English. 10/2013

Please read this manual before operating your device, and keep it for future reference. Understand all safety precautions before using your device to ensure safe and proper use. Graphics used in this manual are for illustration purposes. The actual products may vary.

Safety precautions

When using your device while driving, follow local regulations in the region you are in.

•Never disassemble or modify your device for any reason. Doing this may cause the device to malfunction or become combustible. Bring the device to an authorised service centre to repair it.

•Keep your device and all accessories out of the reach of small children or animals. Small parts may cause choking or serious injury if swallowed.

•Avoid exposing your device to very cold or very hot temperatures (below 5 °C or above 35 °C).

Extreme temperatures can cause the deformation of the device and reduce the charging capacity and life of your device.

•Do not allow your device to get wet — liquids can cause serious damage. Do not handle your device with wet hands. Water damage to your device can void your manufacturer’s warranty.

•Avoid using your device’s light close to the eyes of children or animals.

•Do not use the device during a thunderstorm. Thunderstorms can cause the device to malfunction and increase the risk of electric shock.

Excessive exposure to loud sounds can cause hearing damage. Exposure to loud sounds while driving may distract your attention and cause an accident. Use only the minimum volume setting necessary to hear your conversation.

Instructional icons

Before you start, familiarise yourself with the icons you will see in this manual: Warning—situations that could cause injury to yourself or others

Caution—situations that could cause damage to your device or other equipment

Note—notes, usage tips, or additional information

Getting started

Your device overview

 

Charging socket

Talk button

cover

Speaker

Pen clip

 

Volume button

 

Secondary

Primary

microphone

microphone

 

Side button

 

 

Pen nib

•Make sure you have the following items: device, replacement nibs, nib extractor tool, travel adapter and user manual. The supplied items may vary.

•Do not apply any excessive pressure to the Pen clip.

Button functions
Button

 

Function

 

•

Press to turn the device on or off.

 

•

With the device turned off, press and hold for 3 seconds to

Talk

 

enter Pairing mode.

•

Press to answer or end a call.

button

•

Press and hold to reject an incoming call.

 

 

•

Press and hold to place a call on hold.

 

•

Press and hold to switch between calls.

Volume

•

Press to adjust the volume.

button

•

Press and hold to turn the microphone on or off during a call.

Side

•

Press and hold to perform various S Pen actions.

button

 

 

 

 

 

Using your device

•Activated functions and features may differ depending on the phone type.

•Some devices, especially those that are not tested or approved by the Bluetooth Special Interest Group (SIG), may be incompatible with your device.

To ensure you get the best performance from your device

•Keep the distance between your device and device as small as possible and avoid placing your body or other objects in the signals path.

•Covering your device could affect its performance so keep contact to a minimum.

Using the device as the S Pen

S Pen offers all the great features of your device in addition to traditional controls, such as tapping or flicking. Hold the pen in location where you can press the side button by your thumb or forefinger.

Press and hold the side buttons to perform the following actions.

•Back : Drag the S Pen to the left to return to the previous screen.

•Menu : Drag the S Pen up to access a list of options.

•Screen capture : Tap and hold the screen to capture a screen shot.

•Quick memo : Double-tap to launch the quick memo function.

S Pen may function differently or malfunction depending on the device and applications when in use.

Replacing the pen nib

1Grasp the tip of the nib in the device with the groove of nib extractor tool and gently pull the nib out.

2Insert a new nib into the tip of the device where you just removed the old nib until it clicks

•The black nib should be replaced with new one, if the white portion becomes worn out.

•Do not insert the round end of the pen nib into the device. This may damage the device.

•Do not over press the nib when you insert the tip into the device.

•Be careful not to clip your finger into the nib extractor.

•Do not re-use old pen nibs. Used pen nibs might cause your device to malfunction.

Pairing and connecting the device

Pairing means a unique and encrypted wireless connection between two Bluetooth devices when they agree to communicate with each other.

In Pairing mode, two devices should be placed close enough.

Pairing and connecting the device with a phone

1Enter Pairing mode. The indicator light turns blue and stays for 3 minutes.

•With the device turned off, press and hold the Talk button for 3 seconds.

•With the device turned on, press and hold the Talk button and Volume up button at the same time for 3 seconds.

2Activate the Bluetooth feature on your phone and search for the device (see your phone’s user manual).

3Select the device (HM5100) from the list of devices found by your phone.

•If requested, enter the Bluetooth PIN 0000 (4 zeros) to pair and connect the device to your phone.

•Once pairing is completed, the device will attempt to reconnect each time you turn it on.

Pairing via the Active pairing feature

With the Active pairing feature, your device automatically looks for a Bluetooth device within range and tries to make a connection with it.

Make sure the phone’s Bluetooth visibility option is set on.

•In Pairing mode, press and hold the Talk button. The indicator light colour changes to violet from blue.

•The Bluetooth phone you want to connect with must not be paired with other devices. If the phone is already connected to another device, end the connection and restart the Active pairing feature.

•This feature may not be supported on some devices.

-1-

-2-

-3-