Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
STOP | |
Samsung Electronics America, Inc. | |
Please do not return this unit. | 85 Challenger Road Ridgefield Park, NJ |
Samsung Electronics Canada Inc. | |
If you have problems operating your | 55 Standish Court Mississauga, Ontario L5R 4B2 |
TV, call: | Call Center hours of operation: |
Step 4: Connect External Devices
Connecting an AV device (DVD/ Blu-ray player, cable/satellite box, etc.)
Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced Sound quality.
Analog Audio connection
Using an Audio Cable
AM EST. | ||
To register this product, visit: www.samsung.com/ | ||
For web support please visit: | ||
register. | ||
www.samsung.com/support | ||
|
Step 1: Install the Stand
Follow the steps below to connect the TV to the stand.
✎✎NOTE
xx Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them.
xx Make sure that at least two persons lift and move the PDP TV.
xx Stand the product up and fasten the screws. If you fasten the screws with
the PDP TV placed down, it may lean to one side. | |
1 With your TV upright, connect the | 2 Fasten the two screws (M4 X L16) |
TV to the Stand as shown. | at position 1, and then fasten the |
| two screws (M4 X L16) at position |
| 2. |
Audio Cable
(Not Supplied)
HDMI to DVI Cable 
(Not Supplied)
Very Good Connection
HD connection (up to 720p/1080i)
Using a HDMI to DVI Cable
Device | DVI OUT |
AUDIO OUT |
Good Connection
Component connection (up to 720p/1080i)
Using a Component Cable
DVD /
Device | COMPONENT OUT AUDIO OUT |
|
|
| Best Connection |
|
| HD connection (up to 720p/1080i) |
|
| Using an HDMI Cable |
HDMI Cable |
| DVD / |
| ||
(Not Supplied) | ||
|
| |
HDMI OUT | Device |
|
Audio Cable (Not Supplied)
Video Cable (Not Supplied)
Lowest Quality Connection
Audio/Video connection (480i only)
Amplifier / DVD Home Theater
Audio Cable (Not Supplied) | AUDIO IN |
Digital Audio connection
Using an Optical Cable
Digital Audio System
Optical Cable (Not Supplied)
OPTICAL
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
HD connection
Using a HDMI to DVI Cable
s |
|
|
s |
|
|
s |
|
|
s |
|
|
| s |
|
Front | s | s |
| s |
Rear | 2 |
|
1 |
Using an Audio/Video Cable
| DVD, |
| |||
| satellite receiver, VCR |
| |||
Audio Cable (Not Supplied) | VIDEO OUT |
| AUDIO OUT |
| Device |
|
| ✎✎When connecting to AV IN on the back of your TV, attach the |
Component Cable (Not Supplied) | ||
|
| video cable (yellow) to the green jack next to the AV IN label. |
|
| The jack will not match the color of the video cable (yellow). |
Audio Cable (Not Supplied)
AUDIO OUT
HDMI to DVI Cable (Not Supplied)
DVI OUT
Step 2: Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1.Lift the cover on the back of the remote
upward as shown in the figure to the right.
2. Install two AAA batteries. |
✎✎ Make sure to match the + and - |
Step 5: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV’s channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the ENTEREbutton.
✎✎Most cable systems are Standard(STD) systems, If you are not sure about what kind of cable system you have, contact your cable company.
✎✎If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box.
7 Select the time zone in which you live, and then press ENTERE.
8 After the time zone screen, The connection method for best HD screen quality is displayed. Press Right arrow button on your remote to view each screen in succession. Press the Blue button to skip this section.
ends of the batteries to the diagram in the battery compartment. |
3. Replace the cover. |
To skip a screen, press the MENU button. To turn on your TV, press the POWER button on the remote or on the TV. To run Plug & Play, follow these steps:
4
The TV memorizes the available
Plug & Play
9 The Enjoy your TV. screen appears. Then press the ENTEREbutton.
Step 3: Connect Power and Antenna or Cable
VHF/UHF Antenna
Connect Ant In to
|
|
|
|
| • | Wall cable jack |
|
|
|
|
| • | VHF/UHF Antenna |
|
|
|
|
| ||
|
|
| or |
| • | Cable or Satellite box |
|
|
|
|
| ||
Best to use 75 ohm (round) cable. |
| Ant or Cable Out | ||||
|
| |||||
Make sure the AC power cord is plugged in securely to the wall outlet and the TV.
Antenna Cable (Not Supplied)
1 Using your remote control, select the language for the On Screen Display (OSD), and then press the ENTEREbutton.
2 Select Home Use, and then press the ENTEREbutton. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes.
3 Select the Antenna Source to memorize. you must select Antenna Source to same type as your cable system type. After selecting source, select Start; then press the ENTERE button on your remote.
|
| Plug & Play |
|
|
|
|
| Select Language of the OSD. |
|
|
|
|
|
|
|
| |
|
| English |
|
| |
|
|
|
|
| |
|
| Language | Español |
|
|
|
|
| Français |
|
|
|
|
|
|
|
|
|
|
| UMove EEnter | ||
Plug & Play
Select ‘Home Use’ when installing this TV in your home.
Store Demo | Home Use |
|
|
| LMove EEnter |
Plug & Play
Select the Antenna source to memorize.
Air | Start |
Cable | Start |
Auto | Start |
|
|
UMove | EEnter mSkip |
5
6
channels. This process can take up to 45 minutes.
After the TV has memorized the channels, choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don’t, or if you have a cable or satellite box. When done, press the ENTEREbutton.
✎✎ If you select Manual, the clock setting screen appears.
Select the daylight savings time setting: Off, On or Auto and then press the ENTERE button.
Auto Program in Progress. |
| |
DTV Air : | Air : |
|
DTV Cable : | Cable : | Cable : 35 |
48%
Stop
EEnter mSkip
Plug & Play |
|
|
Set the Clock Mode. |
|
|
Clock Mode | Auto |
|
Manual |
| |
|
| |
UMove | EEnter | mSkip |
| Plug & Play |
|
|
| Set to daylight saving time. |
|
|
|
|
| |
| Auto |
| |
|
|
| |
| DST | On |
|
|
| Auto |
|
|
|
|
|
| UMove | EEnter mSkip | |
If You Want to Rerun Plug & Play
1.Press the SOURCE button on your remote, then select TV mode.
2.Press the MENU button on your remote to display the menu.
3.Press the ▲ or ▼ button to select Setup, and then press the ENTERE button.
4.Press ENTEREagain to select Plug & Play.
