Prevention of Afterimage Burn-in

Black Matrix

Common

Color-Filter

 

 

 

Electrode (ITO)

 

 

 

 

 

 

 

 

 

 

 

 

 

Source Drain

 

 

 

Gate

Pixel Electrode (ITO)

Storage

 

 

 

Capaccitor (Cs)

TFT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Data Bus-Line

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

What is afterimage burn-in?

Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period of time (more than 12 hours), a slight voltage difference may occur between the electrodes in pixels that control the liquid crystals.

Such a voltage difference between electrodes increases with time and makes the liquid crystals thinner. When this occurs, a previous image can remain on the screen when the pattern changes. To prevent this, the accumulated voltage difference should be reduced.

――Afterimage burn-in should not occur when an LCD panel is operating in proper conditions.

Preventing afterimage burn-in

――The best way to protect the product from afterimage burn-in is switching the power off or setting the PC or system to run a screen saver when not in use. Also, Warranty service may be limited depending on instruction guide.

•• Powering Off, Screen Saver and Power Saving Mode

-- Power off the product for 4 hours after using it for 20 hours. -- Power off the product for 2 hours after using it for 12 hours.

-- Go to Display Properties > Power Supply on your PC and set the product to power off as required. -- Using a screen saver is recommended.

It is best to use a single-color or moving-image screen saver.

•• Regular color Change -- Use 2 colors

Switch between 2 colors every 30 minutes as shown above.
Type 1FLIGHT TIMEOZ348 20:30UA102 21:10

Type 2

FLIGHT TIME

OZ348 20:30

UA102 21:10

159