Samsung MX-J730/XN manual Using the NON-STOP Relay Function, Auto Change Function, Software Update

Using the NON-STOP RELAY Function

The NON-STOP RELAY function plays music con- tinuously without an interval between tracks/files. For example, for two successive music files, the function skips to a position 10 seconds after the start of the second file when there are 10 seconds of playing time left in the first file.

1.Press the NON-STOP RELAY button on the remote control.

Each time you press this button, the mode changes as follows:

ON-NON-STOP MUSIC RELAY ; OFF-NON- STOP MUSIC RELAY

2.To cancel this function, press the NON-STOP RELAY button until “OFF-NON-STOP MUSIC RELAY” is displayed.

•This function is only available during playback of a CD/USB.

Auto Change Function

You can play a disc followed by a USB continuously.

1.Press the AUTO CHANGE button, and then use , , . buttons or [, ] buttons to select a

setting, and then press to apply your

selection.

•If My List Play has not been set in CD/USB mode, the settings change as follows:

AUTO CHANGE OFF ; ALL

•If My List Play has been set in CD/USB mode, the settings change differently:

AUTO CHANGE OFF ; ALL ; MYLIST

•When the AUTO CHANGE mode is "ALL", the Hi-Fi Component will play music from DISC, USB1, and USB2 continuously.

•When the AUTO CHANGE mode is "MYLIST", the Hi-Fi Component will play My List tracks from DISC, USB1, and USB2 continuously.

•When the auto change mode is "ALL/MYLIST", if you press the POWER button, FUNCTION button, or the OPEN/ CLOSE button, the auto change function automatically switches to "OFF" mode.

•When the USB is playing, if you disconnected the USB, the auto change function automatically switches to "OFF" mode.

•When the auto change mode is "ALL/MYLIST", the unit cannot record.

•When the auto change mode is "ALL/MYLIST", the REPEAT function automatically change to OFF.

•When the auto change mode is "ALL/MYLIST", the DELETE, USB REC, MY LIST and REPEAT functions do not work, and the unit displays "ALL/MYLIST-AUTO CHANGE".

•When DISC play ends, if there's no USB 1, the unit will play music from USB 2.

•When DISC play ends, if there's no USB 1 and USB 2, the unit will continue to play the disc.

•When USB 2 play ends, if there's no DISC, the unit will play music from USB 1.

Software Update

Samsung may offer updates for the Product's system firmware in the future.

If an update is offered, you can update the firmware by connecting a USB device with the firmware update stored on it to the USB port on your product.

Note that if there are multiple update files, you must load them onto the USB device singly and use them to update the firmware one file at a time.

Please visit samsung.com or contact the Samsung Call Center to receive more information about down- loading updates files.

•Select USB function, insert a USB device containing the firmware update into the USB port on the main unit.

•Updating firmware may not work properly if audio files supported by the product are stored in the USB storage device.

•Do not disconnect the power or remove the USB device while updates are being applied. The main unit will turn off automatically after completing the firmware update.

•After the update, all settings are reset to their factory default settings. We recommend you write down your settings so that you can easily reset them after the update.

If the firmware fails to update, we recommend formatting the USB device in FAT16/FAT32 and trying again.

•Once the software update is completed, turn on the product with no disc inserted. The “NO DISC” message appears on the display. Press and hold the STOP button on the main unit for longer than 5 seconds. “INIT ” appears on the display and the unit powers off. The upgrade is complete.

•Do not format the USB device in the NTFS format. The product does not support the NTFS file system.

•Depending on the manufacturer, some USB devices may not be supported.

•The product has a DUAL BOOT function. If the firmware fails to update, most functions will become inoperable and "UPGRADE FIRMWARE" will appear on the display. Update the firmware again.

English 19