3-16
E
3-15
FOCUS MODE
In the FOCUS MODE MENU, the Focus method can be set to ONEAF(One Auto
Focus), or MF(Manual Focus).
- ONEAF : In the ONEAF mode, it automatically sets the focus after the zoom moves,
and operates as the same in the MF mode if the zoom does not move.
- MF : In MANUAL FOCUS MODE the user adjusts the Focus manually.
Use the left/right keys to select ONEAF orMF in the FOCUS MODE menu.
(VIDEO SET)
IRIS ALC...
SHUTTER
OFF
AGC
LOW
WHITE BAL ATW1
DIS OFF
FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT

SPECIAL

In SPECIAL menu, you can directly adjust REVERSE, Y-LEVEL, C-LEVEL,
and DETAIL functions.
- REVERSE: Mirrors the screen horizontally, vertically, or in all directions.
- Y-LEVEL : It is used to set the levels for the Sync signal and the entire
brightness signal of the video signal.
- C-LEVEL : It is used to set the levels for the Burst signal and the entire colour
signal of the video signal.
- DETAIL : Controls both horizontal and vertical distinction.
➜
Press
[Enter]
(VIDEO SET)
IRIS ALC...
SHUTTER OFF
AGC LOW
WHITE BAL ATW1
DIS OFF
FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT
(SPECIAL)
REVERSE OFF
Y-LEVEL (0)I--------
C-LEVEL (0)I--------
DETAIL (2)--I-
RET
DIS
The DIS(Digital Image Stabilization) function compensates the camera
screen shaking incurred from vibration.
❈It is recommended to deactivate the DIS function in the no vibration
environment.
❈From VIDEO SET, if you set SHUTTER to between AUTO X2... and
AUTO X128... DIS will be displayed as “---“ (it can operate only in
Off mode). You can’t adjust the settings manually.
➜
Press
[Enter]
(AWB/MANU)
PRESET 3200K
RET
(VIDEO SET)
IRIS ALC...
SHUTTER
OFF
AGC
ON
WHITE BAL MANU...
DIS ON
FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT
You can select one of four modes for white balance adjustment as follows:
- ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the
color temperature is monitored continuously and thereby white balance is
set automatically. The following are the approximate supported color
temperature ranges in these modes.
ATW1 : 2500K ~ 9300K(
✻
1)
ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(
✻
2)
✻
1. If the color temperature is out of this range in ATW1 mode, proper
white balance may not be obtained. In that case, select ATW2 mode.
✻
2. In ATW2 mode, if one color is dominated in the shooted area, the
color can be displayed differently.
Therefore, select the mode which is appropriate for the environment.
- AWC(Auto-Tracing White Balance Control): In this mode, accurate white
balance is obtained by pressing [ENTER] while having a white paper in
front of the camera. White Balance data will be maintained after set it
once. AWC mode is best in locations where the color temperature of light
source is constant.
- MANU : If WHITE BAL menu is set to MANU mode, the user can set the
white Balance considering the current illumination. Select MANU item
and press [ENTER], the sub screen where you can select Manual White
Balance will be shown. Use the left/right keys to select 3200K, 5600K or
OFF(USER) mode in the PRESET menu.
- 3200
K
: Set color temperature to 3200
K
- 5600
K
: Set color temperature to 5600
K
- USER : Choose out a proper value from the RED and BLUE graph for
color and temperature setup.
❈
The ONEAF setting can be selected only when OFF,
1/100(1/120)~1/10K, AUTO X2 is selected for the SHUTTER menu. Any
Other SHUTTER setting(AUTO X4~AUTO X160) causes MF to be
selected automatically for the FOCUS MODE menu.
❈
ONEAF function may not possible withe types of objects listed below. For
such objects, focus manually.
- High intensity objects or objects illuminated with low lighting
- Obejects shot through wet or dirty glass
- Pictures that are a mixture of distant and nearby objects
- White alls and other single-color objects
- Venetian blinds and other horizontally striped objects
00600A-SCC-C6407-ENG 8/17/06 3:27 PM ˘` 3-15