Samsung SD-616 technical specifications Safety Precautions Your DVD-ROM Drive

DVD-ROM DRIVE
	Safety Precautions	Your DVD-ROM Drive
SD-616

The following diagrams illustrate the precautions to be taken when using your DVD-ROM drive.

Upgrading the Firmware Flash Memory

The product firmware can be upgraded by downloading the updated file from the following Web site:

http://www.samsungodd.com

www.samsungelectronics.com

System Requirements

Before you install the DVD-ROM drive, we strongly recommend that you check that your setup meets the system requirements listed below.

Connecting the Cables

1.	Power cable
2.	Master/slave select terminal

3.IDE cable

4.Audio cable

User's Guide

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran- tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Re-orient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

http://www.samsungodd.com

www.samsungelectronics.com

BG68-00342A Rev.03

✱Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

You must not use the drive in any manner other than that specified in this guide.

CAUTION Do not attempt to repair the DVD-ROM drive yourself. Contact your dealer or local SAMSUNG representative for all repairs.

If you make any adjustments or perform any operations other than those specified in this guide, you run the risk of exposure to hazardous radiation.

Avoid exposing your eyes or skin to direct or scattered radiation.

WARRANTY Please refer to the Samsung limited warranty statements.

Precautions 1. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

2.Always check each disc for cracks before using it. If there are cracks on the surfaces, especially around the border of the cen- ter hole, we recommend that you make a copy of the disc immediately and then stop using it. If you continue using the disc, it will probably develop more cracks and eventually cause irreparable damage.

3.Do not use poor quality discs:

●From unknown sources

●Without any copyright

●Scratched or damaged in any way

1

1 2 3 4 5 6

1.Connector for stereo headphones with a 3.6 mm stereo mini-jack

2.Headphone volume control

3.Disc compartment (the compartment opens and closes automatically when you press the Eject button)

4.Emergency eject hole (if the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmly)

5.Indicator light (when it is green, a disc is being read)

6.Eject button

1 2 3 4 5

1. Two-pin digital audio output terminal for use with a sound or MPEG card supporting digital audio features

2. Four-pin sound output terminal for use with a sound card (refer to the sound card documentation for further details)

3. Master/slave select terminal

4. 40-pin host IDE interface connector

5. 4-pin power terminal

2

Item	Description
Computer	Intel Pentium III (or higher), 350MHz or higher,
	128	MB of RAM (or higher) with an IDE interface
Disk space	100	MB minimum
Windows version	Windows 95 OSR2 / 98 / 2000 / ME / XP
	/Windows NT 4.0 (or higher)

*This product has been set at the UDMA mode. It may cause trouble due to

the compatibility of a specific board or system. In this case, download the latest version of “Firmware” which supports the DMA Mode.

Using the DMA mode may slightly decrease the efficiency of DVD-ROM.

Installing the DVD-ROM Drive

To install your DVD-ROM drive in the PC, proceed as follows.

1 Make sure that the PC is powered off and disconnected from any power source.

2 If necessary, attach a horizontal bracket to both sides of the drive.

●Use of the brackets depends on your computer model; you can purchase these accessories separately from your computer dealer.

3 Remove the cover from a free expansion slot and install the DVD-ROM drive, as shown in the illustration.

●If you have no free expansion slot, install the drive in place of the diskette drive.

DVD-ROM drive

3

1 Connecting the power cable

The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal on the rear of the DVD-ROM drive.

2 Installing a jumper on the master/slave select terminal

Install the jumper in the correct position on the terminal:

MA to use the device in the master mode

SL to use the device in the slave mode

CS to control the device via a CSEL host interface signal

See Step 3 for further details.

3 Connecting the IDE cable

Two configurations are possible.

●The DVD-ROM drive is the only IDE device in addition to the hard disk.

	Install the jumper in the SL position (Slave).
IDE port	Connect the 40-pin flat IDE cable from the IDE port
Mother board	on the mother board, first to the DVD-ROM drive
	and then to the hard disk.

DVD-ROM	Hard disk
(SL)	(MA)

●You already have an additional IDE device installed in your computer.

Second IDE cable First IDE cable

			Install the jumper in the MA position (Master).
			Connect the 40-pin flat IDE cable from a second
		Mother	IDE port on the mother board directly to
			the DVD-ROM drive or first to another additional
		board
DVD-ROM CD-ROM			IDE drive and then to the DVD-ROM drive.
		Hard disk	Hard disk
(MA)	(SL)	(SL)	(MA)

4 Connecting the audio cable from a sound card

Connect the 4-pin audio cable between the sound output terminal on the DVD- ROM drive and the audio input terminal on the sound card.

4

Setting Up the Device Driver

◆Automatic Setup

1Insert the setup diskette in the diskette drive and change the directory to A:, where A: is the diskette drive.

To do so, type A: after the C:\ prompt and press [Enter].

2Type CDSETUP and press [Enter].

3Reboot the computer.

◆Manual Setup

1 Make the C:\SAMSUNG directory.

2 Copy the files from the diskette to the C:\SAMSUNG directory.

To do so, type COPY A:*.* C:\SAMSUNG after the C:\ prompt and press [Enter].

3 Edit the CONFIG.SYS file.

Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry.

LAST DRIVE = Z

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V

4 Edit the AUTOEXEC.BAT file.

Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry.

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

C :\SAMSUNG\MSCDEX /D:SSCD000

5 Reboot the computer.

Installing the Device Driver

No additional device driver is needed for Windows 95/98/XP/NT, as the default Windows device driver is used. You can check that the DVD-ROM drive has been correctly detected by Windows. To do so, proceed as follows.

1 Double-click on the My Computer icon on your desktop.

2 Double-click on the Control Panel folder.

3 Double-click on the System icon.

4 Click on the Device Manager tab.

5 Expand the CD-ROMbranch.

The SAMSUNG DVD-ROM SD - *** device name is displayed.

The SAMSUNG device driver enables discs in the DVD-ROM drive to be read but not recorded in an MS-DOS environment; the driver is located in the D driver folder on the CD record utility disc.

DVD Region Protection Coding (RPC):

The RPC feature is supported on DVD players and is used with DVD-video discs (such as movies). Currently, the motion picture industry has divided the world into different regions or zones that correspond to the regional markets into which the motion picture industry releases movies. Simply put, RPC codes are placed on movies marketed throughout the world, based on the region of the world in which they are being sold. These RPC codes help control and pre- vent pirating of new movies into other motion picture regions prior to their true release dates within those markets.

The SD-616 DVD-ROM drive supports RPC phase II. In the RPC-2 mode, the local code can be changed by users. RPC-2 is selected by default for the SD-616 DVD-ROM drive. You can change the region code up to five times via an MPEG application.

Please contact your dealer or local SAMSUNG representative if you wish to change the local code more than five times.

Using the DVD-ROM Drive

To play audio or video CDs in your DVD-ROM drive, proceed as follows.

1 Push the power button and boot the computer.

2 After booting the computer, open the disc compartment by pressing the Eject button.

3 Insert the disc (CD/DVD) with the label on the disc facing upwards and close the disc compartment by pressing the Eject button.

The indicator light comes on.

4Play the disc (CD/DVD).

Playing Audio CDs

Run the CD player supplied with Windows or your sound card. You can listen to the CD by connecting headphones to the appropriate connector. If you have installed the appropriate player, such as Microsoft Windows Media Player, you can adjust the volume using the headphone volume control on the drive front panel.

Playing Video CDs

Set up and run the SOFT MPEG program.

Storing and Cleaning Your Discs

To ensure a long service life for your discs and drive, follow the precautions below when storing and cleaning your discs.

1 Do not place a disc in direct sunlight.

2 Store a disc vertically in a well-ventilated and stable location.

3 Do not write or attach a label on a disc.

4 Do not drop a disc or place heavy objects on it.

5 Do not touch the surface of a disc; hold it by the edges.

6 To clean a disc, polish lightly from the inside

of the disc to the outside with a soft cotton cloth.

7 Do not leave the disc compartment open when you are not using it.

Solving Technical Problems

Problem	Meaning / Solution
The DVD-ROM drive is not	◆ Check that the power, audio and IDE cables are correct-
detected by the computer.	ly connected to the computer.
After installing the DVD-ROM	◆ Change the IDE cable and reconnect it to the computer.
	Preferably, connect a second IDE cable to the DVD-ROM
drive, the PC gets slower.	drive in master mode; see page 7 for further details.
	◆ Check the position of the jumper in the master/slave
	select terminal.
The DVD-ROM drive is not	◆ Reinstall the device driver or update it with the latest
recognized by MS-DOS.	version by downloading it from the Samsung Web site.
	- www.samsungodd.com
	- www.samsungelectronics.com
The DVD-ROM drive is not	◆ This case may occur when there is a Windows instal-
detected by Windows.	lation problem; reinstall Windows.
No sound is heard from an	◆ Check whether the audio cable is correctly connected
audio CD.	to the sound output terminal on the DVD-ROM drive
	and the sound card CD-IN terminal.
	◆ Check that the sound card is operational.
	◆ Adjust the volume control.
A CD is not read or is read	◆ Install the latest version of the device driver.
too slowly.	◆ Check whether the CD is of good quality and clean it,
	if necessary.
The disc compartment will not	◆ Check that the power cable is correctly connected.
open.	◆ Power off and disconnect the PC. Insert a pin or
	unfolded paper clip in the emergency hole and push
	firmly until the disc compartment opens.
When the MPEG software plays a	◆ Adjust the size of the replay screen.
Video CD, the pictures are not regu-	◆ After checking the display resolution, adjust it,
lar and the running speed is too slow.	if necessary.
The Disc is not in message is	◆ The computer may not recognize the disc if you start
displayed even though a disc	playback too quickly after inserting the disc.
has been inserted.	Open and close the disc compartment and try again.
	◆ Clean the disc and try again.
The DVD-ROM drive is not	◆ The interface mode of the sound card is AT-BUS.
detected after it is connected	You must therefore connect the DVD-ROM drive to
to a sound card.	the IDE port on the PC mother board, rather than to
	the sound card, or install an IDE-compatible sound
	card.

Technical Specifications

SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice.

ITEM			SD - 616
			DVD / CD
			DVD-ROM, DVD-VIDEO, CD-DA(Audio), CD-ROM, CD-ROM XA,
	Disc types supported		CD-Plus, CD-Extra, Photo-CD(Single,Multi-session), Video CD ready,
DISC			Enhanced CD, CD-I/FMV, CD-R,CD-RW. CD-TEXT.
	Disc diameter		120mm or 80mm
			Sustained :
			Max. 21,600KB/sec (16X)	/ Max. 7,200KB/sec (48X)
	Data transfer rate
			PIO Mode 4 : 16.6MB/sec
			Multiword DMA mode 2 : 16.6MB/sec
			UDMA mode 2 : 33MB/sec
DRIVE	Access time(1/3stroke)		90ms(Typical) /	90ms(Typical)
PERFORMANCE	Data buffer capacity		512KB
	Laser		Semiconductor Laser
	Slide mechanism		Stepping motor
	Spindle motor		Brushless motor
	Loading mechanism		Tray. DC motor(Soft Eject). Horizontal/Vertical
ERROR RATE			10-15 / MODE1:10-12, MODE2:10-9
	Eject button		Auto eject or Auto inject
FRONT PANEL	Indicator(LED)		BUSY
	Headphone output		Stereo mini-jack(Ø3.6mm)	0.60V±20%(rms) 33 Ω
	Volume control		Wheel knob
	Required power		+5VDC : 2.0A, +12VDC : 1.0A
REAR PANEL	Interface connector		ATAPI
	Audio output		Line out 0.70V ± 20%(rms) : 47KΩ
	Jumper block		Device configuration jumper
OPERATING	Operation		Temperature : 5 ~ 45°C,	Humidity : 8 ~ 80%
ENVIRONMENT	Storage		Temperature : -20 ~ 55°C,	Humidity : 5 ~ 85%
	616B/F	Dimensions	148,2(W) x 42(H) x 202(D)mm
GENERAL		Net weight	880g
	616T	Dimensions	148,2(W) x 42(H) x 184(D)mm
		Net weight	750g
RELIABILITY	MTBF		125,000 POH(Duty 20%)

* In case of the PC without UDMA, it may have a different DVD data transmission rate.

5 6 7 8 9