Samsung SH-S202G(TS-H652G) technical specifications Safety Precautions, Introduction, Rear, Front

SH-S202G(TS-H652G)ENG/RUS 2007.4.15 11:28 PM Page 1

Super- DVD Writer

SH-S202G(TS-H652G)

User Guide - ENGLISH

Safety Precautions

The following are basic precautions to ensure user safety and reduce the risk of property damage.

When you install the drive

Warning/Caution

Warning: To warn the user that failure to comply with the instructions may result in serious injury or death.

Caution: To caution the user that failure to comply with the instructions may result in damage to property.

Introduction

•Design and specifications are subject to change without prior notice.

Disc compartment Eject Button

Connecting the Cables to the DVD WriterConnecting the Cables

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Re-orient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Change or modifications not expressly approved by the manufacturer responsible for compliance could void the user ’s authority to operate the equipment.

LASER STANDARD

IEC 60825-1 :1993 +A1 :1997 +A2 :2001

WEEE

Correct Disposal of This Product (Waste Electrical &Electronic Equipment)

Place the drive on a level surface.

•	Failure to do so may cause the	• Avoid high-humidity environments.
	device to fall onto a hard surface,
	resulting in damage or malfunction.

While operating

•	If the power cable is not connected
	properly, it may cause a fire or
• Avoid low- or high-temperature	damage the drive. Check the direction
environments.	of the power connector and the drive
	incline before connection.
	+5V DC	Ground
	Ground	+12V DC

Do not drop the drive, and protect it fromsevere shocks.

•It can damage the drive or cause it to malfunction.

Do not move the drive while in operation and do not attempt to open the disc tray byforce. Make sure to close all working programs before attempting to open the tray and always use the open/close button.

•Never allow food particles or foreign substances to enter the drive casing.

•To protect against the risk of fire, do ot spill such liquids as alcohol and benzene on the drive.

Front

Disc compartment Emergency eject hole LED

If the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmlhy)

Sound output terminal Interface terminal

Power cable

EIDE cable

Master/slave select terminal

Audio cable

1Connecting the power cable

•The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal the rear of the DVD Writer.

2 Connecting the EIDE cable

• Insert the EIDE cable, which is connected to the hard

(Applicable in the European Union and other European countries with separate collection systems)

Do not insert a pin into the emergency opening while in operation.

disk to the interface terminal.

(Place the red line of the cable close to the Pin 1.)

This marking shown on the product or its literature,indicates that it should not be disposed with other household wastes at the end of its working life.To prevent possible harm to the environment or human health from uncontrolled waste disposal,please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product,or their local government office,for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.This product should not be mixed with other commercial wastes for disposal.

•Samsung Eco-mark

The Samsung’s own Eco mark helps consumers to easily understand that Samsung develops eco-friendly products. This mark represents Samsung’s

continuous effort to develop eco-friendly products.

• RoHS

(Restriction of the use of certain hazardous substances in electrical and electronic equipment)

The RoHS, the environment regulation announced by European Union, restricts the use of

Other

	Handle with caution to prevent
• Do not place the drive in	damage from external shock.
direct sunlight.

Do not use cracked, distorted or damaged discs.

In particular, a disc with a crack on the inner tracks may break while in use.

Do not disassemble, attempt to repair or modify the device without express approval as directed in the manual.

•To reduce the risk of damage, electric shock, and fire.

Rear

Digital output Master/slave select terminal	Power terminal
terminal

Accessories

User Guide, Screw 4ea

3Installing a jumper on the master/slave select terminal

•Connect a jumper to the rear side of the DVD Writer.

If the jumper is connected to MA (Master), it will work in the Master mode. If the jumper is connected to SL (Slave), it will work in the Slave mode.

If the jumper is connected to CS (CSEL), you can control the device by using the host interface signal CSEL. (In general, connection to MA is recommended.)

CS : Cable Select(CSEL)

SL : Slave

MA: Master

lead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in products put on the

market in The European Union after July 1, 2006.

BG68-01416A REV.00

- http://www.samsung-ODD.com - http://www.samsung.com

• Any change or modification not expressly approved by designated qualified personnel could			1.	Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended that
void your authority to operate this device.				you make a copy immediately and use the copy instead. When a cracked disc is used continuously,the size of the crack is likely to grow and it
Important to read and understand		Do not disassemble		will eventually result in irreparable damage to the disc.
at all times			2.	Do not use low quality discs (i.e., illegal products, scratched or damaged discs).
	1
				2

Design and specifications are subject to change without prior notice.

* To write with the highest speed(20X), you must use 80 pin E-IDE cable.

3

4Connecting the EIDE cable from a sound card

•Connect the 4-pin audio cable between the sound output terminal on the DVD Writer and the audio input terminal on the sound card.

4

When using one EIDE cable

•Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the DVD Writer.

Slave Drive (Choose the SL Jumper)

Hard Drive MainBoard

When using two EIDE cable

•Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear of the DVD Writer.

- If there is only one Optical drive: select MA (Master).

Master Drive (Choose the MA Jumper)

SEC 1

PRI 1

Hard Drive MainBoard

-If there is two Optical drive, select MA (Master) / SL (Slave).

Master Drive (Choose the MA Jumper)

Slave Drive (Choose the SL Jumper)

SEC 1

PRI 1

(Choose the MA Jumper) (Choose the SL Jumper)

Hard Drive

MainBoard

Installing the Drive

System Requirements

Intel Pentium 800MHz(or higher), 256 MB of RAM (or higher)with an EIDE interface,Windows 2000/ XP/ Vista

Installing the DVD Writer

How to install the DVD Writer on your PC. First, remove the cover; connect the cable to the DVD Writer and then to the PC.

1If necessary, attach a horizontal bracket to both sides of the drive.

•You can purchase these accessories separately from your computer dealer.

(Screws for use: M3 X 6 X 4)

2Remove the plate from a free expansion slot and install the DVD Writer, as shown in the illustration.

•If you have no free expansion slot, install the drive in place of the diskette drive.

•Make sure to use the standardized screws supplied (M3X6). - To use screws other than M3X6 may result in malfunction.

Plate	DVD
	Writer
	Horizontal
	Bracket

Using the Drive/Storing and Cleaning Your Discs

Using the DVD Writer

1Push the power button and boot the computer.

2 After booting the computer, open the disc compartment by pressing the Eject button.

3Insert the disc (CD) with the label on the disc

facing upwards and close the disc compartment by pressing the Eject button. The indicator light comes on.

4Play the disc (CD).

Playing CD-DA/Audio CDs

•Run the CD player program supplied with the sound card or play the Windows Media Player.

Playing Video CDs

•Follow the instructions provided with the disc.

•A video card or MPEG software and a sound card need to be installed to view video CDs.

•If the drive is vertically installed, you cannot use an 8 cm Mini Disc because the disc is movable.

Storing Your Discs

•Do not place a disc in direct sunlight.

•Store a disc vertically in a well-ventilated and

stable location.

• Do not write or attach a label on a disc.

• Do not drop a disc or place heavy objects on it.

Cleaning Your Discs

• Do not touch the surface	• To clean a disc, polish lightly
of a disc; hold it by the	from the inside of the disc to the
edges.	outside with a soft cotton cloth.

•The disc may not function properly if there are fingerprints, foreign substances or dust on the disc surface.

Solving Technical Problems

•The friction noise generated during SPIN-UP and STOP is caused by the Automatic Ball Balancing System(ABS) and is not a malfunction.

The DVD Writer is not	• Check that the power, audio and EIDE cables are correctly
detected by the computer.	connected to the computer.
	• Change the EIDE cable and reconnect it to the computer.
After installing the DVD Writer,	Preferably, connect a second EIDE cable to the DVD Writer
	in master mode.
the PC gets slower.	• Check the position of the jumper in the master/slave select
	terminal.
The DVD Writer is not	• Reinstall the device driver or update it with the latest version
recognized by MS-DOS.	by downloading it from the Samsung Web site.
	- http:// www.samsung-ODD.com
	- http:// www.samsung.com
The DVD Writer is not	• This case may occur when there is a Windows installation
detected by Windows.	problem; reinstall Windows.
A CD is not read or is read	• Check whether the CD is of good quality and clean it,
too slowly.	if necessary.
The disc compartment will	• Check that the power cable is correctly connected.
not open.	• Power off and disconnect the PC.
	Insert a pin or unfolded paper clip in the emergency hole and push
	firmly until the disc compartment opens.
When the MPEG software	• Adjust the size of the replay screen.
plays a Video CD, the pictures	• After checking the display resolution, adjust it, if necessary.
are not regular and the running
speed is too slow.
The Disc is not in message is	• The computer may not recognize the disc if you start playback
displayed even though a disc	too quickly after inserting the disc.
has been inserted.	Open and close the disc compartment and try again.
	• Clean the disc and try again.
The DVD Writer is not	• The interface mode of the sound card is AT-BUS.
detected after it is connected	You must therefore connect the DVD Writer to the EIDE
to a sound card.	port on the PC mother board, rather than to the sound card,
	or install an EIDE compatible sound card.

Technical Specifications

Category		SH-S202G(TS-H652G)
		DVD Writer
		DVD : DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-ROM, DVD-Video,
		DVD+R (Dual), DVD-R (Dual), DVD-RAM, DVD Multi-Border
	Usable Discs	CD : CD-ROM, CD-R, CD-RW, CD-DA, CD+E(G)
DISC		CD-MIDI, CD-TEXT, CD-ROM XA, Mixed Mode CD CD-I,
		CD-I Bridge (Photo-CD, Video-CD),
		Multisession CD (Photo-CD, CD-EXTRA, Portforio),
	Disc Diameter	4.72 Inch or 3.15 Inch (120mm or 80mm)
Interface	Interface Port	ATA/ATAPI (E-IDE)
	PIO mode	PIO Mode 4: 16.6MB/sec
Support
	DMA mode	Ultra DMA Mode 4: 66MB/sec
Access time	CD-ROM	110ms (Random)
(Random)	DVD-ROM	130ms (Random)
	Media Type	Write	Read
	DVD+R	CAV 20X (27.0MB/sec)	CAV 16X (21.6MB/sec)
	DVD+RW	ZCLV 8X (10.8MB/sec)	CAV 12X (16.2MB/sec)
	DVD+R DUAL	ZCLV 12X(16.2MB/sec)	CAV 12X (16.2MB/sec)
	DVD-R DUAL	ZCLV 12X(16.2MB/sec)	CAV 12X (16.2MB/sec)
	DVD-R	CAV 20X (27.0MB/sec)	CAV 16X (21.6MB/sec)
Data transfer	DVD-RW	CLV 6X (8.1MB/sec)	CAV 12X (16.2MB/sec)
	DVD-RAM	PCAV 12X (16.2MB/sec)	PCAV 12X (16.2MB/sec)
rate(MAX)
	DVD-ROM(Single)	-	CAV 16X (21.6MB/sec)
	DVD-ROM(Dual)	-	CAV 12X (16.2MB/sec)
	CD-ROM	-	CAV 48X (7.2MB/sec)
	CD-R	PCAV 48X (7.2MB/sec)	CAV 40X (6.0MB/sec)
	US-RW	ZCLV32X (4.8MB/sec)	CAV 40X (6.0MB/sec)
	HS-RW	CLV 10X (1.5MB/sec)	CAV 40X (6.0MB/sec)
	CD-RW	CLV 4X (0.6MB/sec)	CAV 40X (6.0MB/sec)
Buffer Memory		2MB
Drive Installation		Horizontal / Vertical
Operating	Temperature	41°F ~ 122°F (5°C ~ 45°C)
Environment	Humidity	5% ~ 80% (RH)
Size (Width x Height x Length)		5.83 X 1.65 X 6.69 Inch (148.2 X 42 X 170mm)
Weight		750g

*The product specifications above may be changed improve device performance without prior notice.

5 6 7 8 9