3.

Connect adaptor to the water tap by tightening the screws

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

firmly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Then, turn part (b) following the arrow and put(a) and (b)

a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

together.

b

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Connect the water supply hose to the adaptor. Pull down

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

part (c) of the water supply hose.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When you release part (c) the hose automatically connects

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to the adaptor making a ‘click’ sound.

c

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.

Connect the other end of the water supply hose to the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

inlet water valve at the top of the washer. Screw the hose

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

clockwise all the way in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If the water tap has a screw type faucet, connect the water

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

supply hose to the tap as shown.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

After completing connection, if water leaks from the hose, then repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor.

The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be used.

POSITIONING THE DRAIN HOSE

The end of the drain hose may be positioned in three ways:

Over the edge of a wash basin

The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving.

ln a sink drain pipe branch

The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60 cm above the ground.

ln a drain pipe

Samsung recommends that you use a 65 cm high vertical pipe; it must be no longer than 90 cm.

01 Installing the washing machine

Installing the washing machine _9

Page 9
Image 9
Samsung WD6122CKC, WD6122CKS user manual Positioning the Drain Hose, Over the edge of a wash basin