SanDisk 20-10-00038, Extreme III 3.4 Card Configuration

Interface Description SanDisk CompactFlash Card OEM Product Manual

The PIO data transfer parameters are defined in Table 3-16.

NOTE:SanDisk CompactFlash Memory cards do not assert an -IORDY

signal.

Table 3-16 PIO Data Transfer to/from Device

PIO Timing Parameters Mode 0

(ns) Mode 1

(ns) Mode 2

(ns) Mode 3

(ns) Mode 4

(ns)

t0

a Cycle time (min.) 600 383 240 180 120

t1 Address valid to IORD-/IOWR- setup

(min.) 70 50 30 30 25

t2

a IORD-/IOWR- pulse width 16-bit (min.) 165 125 100 80 70

t2ia IORD-/IOWR- recovery time (min.) --- --- --- 70 25

t3 IOWR- data setup (min.) 60 45 30 30 20

t4 IOWR- data hold (min.) 30 20 15 10 10

t5 IORD- data setup (min.) 50 35 20 20 20

t6 IORD- data hold (min.) 5 5 5 5 5

t6z

b IORD- data tri-state (max.) 30 30 30 30 30

t9 IORD-/IOWR- to address valid hold

(min.) 20 15 10 10 10

a. t0 is the minimum total cycle time, t2 is the minimum command active time, and t2i is the minimum

command recovery time or command inactive time. The actual cycle time equals the sum of the

actual command active time and the actual command inactive time. The three timing requirements of

t0, t2, and t2i shall be met. The minimum total cycle time requirements are greater than the sum of t2

and t2i. This means a host implementation may lengthen either or both t2 or t2i to ensure that t0 is

equal to or greater than the value reported in the devices IDENTIFY DEVICE data. A device imple-

mentation shall support any legal host implementation.

b. This parameter specifies the time from the negation edge of /IORD to the time that the data bus is no

longer driven by the device (tri-state).

3.4 Card Configuration

SanDisk CompactFlash Memory cards are identified by appropriate information in the Card

Information Structure (CIS). The configuration registers are used to coordinate the I/O spaces

and the interrupt level of cards that are located in the system.

02/07, Rev. 12.0 3-20 © 2007 SanDisk Corporation

Contents

Main SanDisk CompactFlash Memory Card OEM Product Manual Page Page Page Table of Content s Page 1.1 General Description 1.2 Features 1.3 Scope 1.4 CompactFlash Standard 1.5 PCMCIA Standard 1.6 Related Documentation 1.7 Functional Description Page Page Page 2.1 System Environmental Specifications 2.2 System Power Requirements Page 2.3 System Performance 2.4 System Reliability 2.5 Physical Specifications Page Page 3.1 Physical Description True IDE Mode Pin Assigments are contained in Table 3-3. Table 3-3 True IDE Mode Pin Assignments 3.2 Electrical Description Page Page Page Page 3.3 Electrical Specification Table 3-8 Output Drive Characteristics Figure 3-1 Power Up/Power Down Timing for Systems supporting RESET Figure 3-2 Power Up/Power Down Timing for Systems not supporting RESET Table 3-10 Common Memory Read Timing Specification signal. Table 3-11 Common and Attribute Memory Write Timing Specification signal. Table 3-12 Attribute Memory Read Timing Specification 3.3.7 Memory Timing Diagrams Figure 3-3 Common and Attribute Memory Read Timing Diagram Figure 3-4 Common and Attribute Memory Write Timing Diagram 3.3.8 I/O Read (Input) Timing Specification Figure 3-5 I/O Read Timing Diagram Table 3-13 contains the read input timing specifications. Table 3-13 I/O Read (Input) Timing Specification 3.3.9 I/O Write (Output) Timing Specification Figure 3-6 I/O Write Timing Diagram Figure 3-7 Register Transfer to/from Device Table 3-15 Register Transfer to/from Device The PIO data transfer parameters are defined in Table 3-16. signal. Table 3-16 PIO Data Transfer to/from Device 3.4 Card Configuration SanDisk CompactFlash Card OEM Product Manual Interface Description 2007 SanDisk Corporation 3-21 Rev. 12.0, 02/07 NOTE:The location of the card configuration registers should always be Interface Description SanDisk CompactFlash Card OEM Product Manual 02/07, Rev. 12.0 3-22 2007 SanDisk Corporation between consecutive cycle operaitons. Table 3-19 Attribute Memory Function Table 3-20 Card Configurations Card Configuration and Status Register (cont) 3.5 I/O Transfer Function 3.6 True IDE Mode I/O Transfer Function 4.1 I/O Primary and Secondary Address Configurations 4.2 Contiguous I/O Mapped Addressing 4.3 Memory Mapped Addressing 4.4 True IDE Mode Addressing 4.5 ATA Registers Page Page Page Page Card (Drive) Address Register (cont) Page 5.1 ATA Command Set Table 5-1 Primary and Secondary I/O Decoding Page Page Page Table 5-8 Identify Device Information Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 5.2 Error Posting Page Attribute Offset Data 7 6 5 4 3 2 1 0 Content Description CIS 2007 SanDisk Corporation 6-1 Rev. 12.0, 02/07 Function CIS Description SanDisk CompactFlash Card OEM Product Manual 02/07, Rev. 12.0 6-2 2007 SanDisk Corporation SanDisk CompactFlash Card OEM Product Manual CIS Description Attribute Offset Data 7 6 5 4 3 2 1 0 Content Description CIS 2007 SanDisk Corporation 6-3 Rev. 12.0, 02/07 Function CIS Description SanDisk CompactFlash Card OEM Product Manual Attribute Offset Data 7 6 5 4 3 2 1 0 Content Description CIS 02/07, Rev. 12.0 6-4 2007 SanDisk Corporation Function SanDisk CompactFlash Card OEM Product Manual CIS Description Attribute Offset Data 7 6 5 4 3 2 1 0 Content Description CIS 2007 SanDisk Corporation 6-5 Rev. 12.0, 02/07 Function Configuration Index 0 CIS Description SanDisk CompactFlash Card OEM Product Manual Attribute Offset Data 7 6 5 4 3 2 1 0 Content Description CIS 02/07, Rev. 12.0 6-6 2007 SanDisk Corporation Function Interface Type SanDisk CompactFlash Card OEM Product Manual CIS Description 2007 SanDisk Corporation 6-7 Rev. 12.0, 02/07 CIS Description SanDisk CompactFlash Card OEM Product Manual 02/07, Rev. 12.0 6-8 2007 SanDisk Corporation SanDisk CompactFlash Card OEM Product Manual CIS Description 2007 SanDisk Corporation 6-9 Rev. 12.0, 02/07 CIS Description SanDisk CompactFlash Card OEM Product Manual 02/07, Rev. 12.0 6-10 2007 SanDisk Corporation SanDisk CompactFlash Card OEM Product Manual CIS Description 2007 SanDisk Corporation 6-11 Rev. 12.0, 02/07 CIS Description SanDisk CompactFlash Card OEM Product Manual 02/07, Rev. 12.0 6-12 2007 SanDisk Corporation SanDisk CompactFlash Card OEM Product Manual CIS Description 2007 SanDisk Corporation 6-13 Rev. 12.0, 02/07 CIS Description SanDisk CompactFlash Card OEM Product Manual 02/07, Rev. 12.0 6-14 2007 SanDisk Corporation SanDisk CompactFlash Card OEM Product Manual CIS Description 2007 SanDisk Corporation 6-15 Rev. 12.0, 02/07 CIS Description SanDisk CompactFlash Card OEM Product Manual 02/07, Rev. 12.0 6-16 2007 SanDisk Corporation SanDisk CompactFlash Card OEM Product Manual CIS Description 2007 SanDisk Corporation 6-17 Rev. 12.0, 02/07 Page Appendix A Ordering Information A.1 SanDisk CompactFlash Memory Card 2007 SanDisk Corporation A-1 Rev. 12.0, 02/07 To order SanDisk products directly from SanDisk, call (408) 801-1000. Page Page Page C.1 SanDisk Corporation Policy