delay, automatic indoor fan speed determined by the system microprocessor, dehumidification mode, washable anti-mold poly filters, indoor mounted operation selector & lamp showing operation, standby & timer modes, with start up test mode & manual on/off switch.

Low Ambient Systems shall be capable of operating in the cooling mode down to zero (0) degrees F. outdoor temperature.

1C) INSTALLATION

System(s) shall be installed according to manufacturer’s instructions & recommendations, as well as, all governing local & national codes. System(s), as well as the infrared remote controller, shall be mounted & placed as shown on plans within all minimum clearances as specified by manufacturer’s instructions, & secured to provide for safe operation. Refrigerant tubing size shall not vary from manufacturer’s specifications, and shall be properly secured & insulated. Installer shall insulate both liquid & suction lines individually. Electrical wiring shall be sized & installed according to manufacturer’s instructions & in conformance with the National Electric Code (NEC)

&local codes. Outdoor condensers shall be mounted & secured to accommodate for extreme weather conditions. Distance between indoor & outdoor unit(s) shall not exceed manufacturer’s specifications.

2)OUTDOOR CONDENSING SECTIONSANYO MODELS C0951, CL0951, C1251,

CL1251, C1852, CL1852

Outdoor condensing section(s) shall be factory assembled, wired, piped & pre-charged with a start up amount of R-22 refrigerant. Unit(s) shall be constructed of G90 galvannealed steel with corrosion inhibiting, powder coated paint. Unit(s) shall be furnished with a high efficiency, Sanyo rotary compressor with internal overload protection, securely mounted with vibration isolators to reduce noise & vibration. Condenser coil heat exchanger shall be constructed of nonferrous, rifled copper tubing with enhanced aluminum slit fins mechanically bonded to the copper. A suction line accumulator, a coil temperature sensor & cap tube metering device shall be factory installed. Fan motor(s) shall be direct drive with internal overload protection, permanent lubrication, with propeller type fans, mounted for horizontal air discharge. Brass valves with refrigeration flare connections & flare nuts, & service ports shall be factory mounted, externally for easy access. The unit(s) shall be test started by the manufacturer at their factory prior to shipment for installation.

2A) Low Ambient outdoor section(s) shall contain a printed circuit board with a sequencer, factory mounted & wired, to assist in control of low ambient operation. Unit(s) shall be able to operate in the A/C mode down to zero (0) degrees Fahrenheit outdoor temperature.

3) INDOOR EVAPORATOR SECTION – SANYO MODELS – KS0951, KS1251, KS1852

Indoor section(s) shall be high wall mount type, factory assembled & wired. Wall mounting fixture, plate & mounting diagram shall be included with each system, as well as wall sleeves to protect wall where tubing passes through. Unit(s) shall contain an evaporator coil heat exchanger constructed of nonferrous, rifled copper tubing with enhanced aluminum slit fins, mechanically bonded to the copper. A single cross-flow blower wheel, statically & dynamically balanced shall be attached to a single direct drive, PSC fan motor, with overload protection, permanent lubrication & multi-speed capability. Unit(s) shall contain a Printed Circuit Board (PCB) with a

-2-

Page 2
Image 2
Sanyo 12KS51, 18KS52, 18KLS52, 12KLS51, 09KLS51 specifications 1C Installation, CL1251, C1852, CL1852

09KLS51, 12KS51, 18KS52, 12KLS51, 18KLS52 specifications

The Sanyo series of air conditioners, specifically the models 18KLS52, 12KLS51, 18KS52, 12KS51, and 09KLS51, exemplify advanced cooling and heating technologies tailored for efficient climate control in various environments. These models are recognized for their robust performance, reliability, and energy efficiency, making them suitable for both residential and light commercial applications.

One of the key features of the Sanyo 18KLS52 and 12KLS51 models is their powerful cooling capacity. The 18KLS52 provides a robust 18,000 BTU cooling capability, ideal for larger rooms or spaces that require significant temperature control. In contrast, the 12KLS51 offers a 12,000 BTU output, suitable for mid-sized areas. Both models incorporate a modern rotary compressor that enhances cooling performance while minimizing energy consumption.

The 18KS52 and 12KS51 split air conditioning units are designed to deliver not only effective cooling but also effective heating with excellent seasonal efficiency ratios. The inverter technology employed in these models adjusts the compressor speed according to the cooling or heating demand, resulting in reduced energy usage and quieter operation. This feature is particularly beneficial in environments that experience fluctuating temperature requirements throughout the year.

For smaller spaces, the Sanyo 09KLS51 model provides a more compact solution without compromising on performance. With a 9,000 BTU capacity, it effectively cools smaller rooms while maintaining a low energy footprint. This model is perfect for dormitories, offices, or bedrooms, where efficient space utilization is paramount.

All Sanyo models in this series come equipped with advanced filters that improve air quality by capturing dust, allergens, and pollutants. The easy-to-clean design of these filters enhances user convenience and ensures a pleasant indoor atmosphere. Furthermore, the ultra-quiet operation of these units makes them particularly desirable for noise-sensitive environments.

In terms of controls, the Sanyo air conditioners include user-friendly remote controls that allow for easy temperature adjustments and settings management, enhancing comfort at the user's fingertips. Energy-efficient designs, combined with thoughtful features, position the Sanyo 18KLS52, 12KLS51, 18KS52, 12KS51, and 09KLS51 models as top choices for consumers seeking effective, reliable, and energy-efficient climate control solutions.