Sanyo CE42LE1 PC OPERA, TION MENU, ALLATION MENU, TION / INST, PC OPERATION /

This monitor can be controlled via the RS232C connector using a

suitable computer/ control commands

Serial Interface Specification

Transfer Specification

1. Transmission Speed: initial setting value is 19200

2. Transmission speed can be changed via Installation menu (see

below)

Connection

The Designated RS-232C serial cable must be used for a

connection to a computer and LCD monitor

The TV command is defined by one command/ one line that starts

with “C” and ends with carriage return (0x0D)

There are two types of commands:

Functional Execution Command e.g Co5[CR] (table on page 63)

Status Read Commands e.g “CR0 [CR] (see table on page 63)

Setting the monitor address in RS232 mode

To Access Installation mode press the greenbutton on the remote

control and hold for 5 seconds. Anew screen will appear.

Each monitor can have a specific Address for example 007, which

enables the monitor to be controlled individually and will not affect

other monitors connected to a controlling PC

Address format command

The addressing format command is used for operating multiple

monitor sets from a single PC via the RS232C command line. If you

set your monitor address to ‘000’, it will never respond to any

addressing command from the PC.

If the address from the PCis ‘FFF’, all monitor sets will execute the

command.

The Address format command is defined by one command, one line

which starts with ‘A’and ends with carriage return.(0 x0D)

The Monitor starts to decode when it receives a carriage return

(0x0D)

An address is added at the top of a control command

Example:

Functional execution command:

“A001C05” [CR] means address is 001 and the control command is

C05

Status read command

“A001CR0”[CR] means address is 001 and command is CR0

The monitor can set its own address in the Installation option menu

(above) The address range is 000 - 999, the default address will be

000

The baud rate indicates the unit for transfer speed of data

from the PC to the monitor sets

This LCD monitor allows you to set up the following:-

■Programme position at Start up

SETTINGPROCEDURE

1. Press and hold the greenbutton on the Remote control

handset for 5 seconds.

Use the 5or 6button to highlight each option, use the

1 or

to switch between each option.

■ On Program

Select ON program using the

6button, select the start up position

using the

1 or 2 buttons.

(Off / AV1 / RGB/ AV2/ AV3/ DVI/ PC)

Press the MENUbutton to exit from the menu.

■ Max Volume

Select Max volume using the

6button, use the

1 or 2

buttons to set the maximum volume required.

■ OSD (On screen display)

Select OSD using the

6button, select ON / OFF using the

1 or

2 buttons.Selecting OFF will inhibit the OSD. To re-instate OSD,

press and hold the green button on the remote control and select

OSD ON.

■ Winter mode

This Function can be activated when the LCD monitor is used during

cold temperature conditions, approximately 38˚F/ 4˚C or below to

maintain picture performance.

Using the eordbutton select winter mode once highlighted you

can select ON or OFF by pressing the 1 or 2button.

IMPORTANT: The AC cord should not be disconnected during the

operation of Winter mode function.

When in winter mode, power consumption is higher than normal

standby consumption. This is entirely due to the operation of heating

circuitry. We strongly recommend to turn off Winter mode when the

ambient temperature is above 38F/4C.

■ RC Inhibition

You can prevent unwanted remote control operation by selecting RC

Inhibition. When selected an inhibit symbol will appear on screen

when a button is pressed on the remote control.

Select using the e or dbutton. Press the 1 or 2button to

select On or OFF.

Press and hold the green button to return to menu to select RC

Inhibition

■Child lock

You can prevent unwanted operation of the LCD monitor via the

buttons on the bottom edge of the monitor.

Select using the eor dbutton. Press the 8button to select On or

OFF.

PC OPERAPC OPERATION / TION / INST

INSTALLA

ALLATION MENUTION MENU

GB GB

RS232C settings

ITEM SPECIFICATION

Synchronous system

Asynchronous

Transmission Speed

9600 / 19200

Data Length 8 bit

Parity None

Stop Bit

Flow Control None

COM 1

TV CONTROL

PORT

(D-Sub 9 Pin) (D-Sub 9 Pin)

RXD

TXD

DTR

DSR

RTS

CTS

RING

N.C.

RXD

TXD

N.C

RTS

CTS

N.C.

ON Program OFF

Max Volume

OSD ON/ OFF

Winter mode ON/ OFF

RC Inhibition ON/ OFF

Child Lock ON/ OFF

/ AV1-AV3 /RGB/ DVI/ PC

Installation

: Select : Adjust : Exit

Address 007

Baud Rate 19200