CONNECTING THE PROJECTOR

Your projector is equipped with various audio/video inputs and outputs including Computer HDB15-pin (VGA) terminals, Monitor HDB15-pin (VGA) terminals and S-VHS video.

CONNECTING THE COMPUTER

CONNECTING TO THE COMPUTER INPUT HDB15-PIN (VGA) TERMINALS (1 and 2)

Personal computers can be connected to the HDB15-pin (VGA) terminal on the projector.

¡Connect the computer to these terminals using the VGA cable and VGA/MAC adapter (not provided).

WARNING: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions. For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable.

CONNECTING TO THE MONITOR OUTPUT HDB15-PIN (VGA) TERMINAL

This terminal contains the information that is viewed on the screen.

An external monitor can be connected to the HDB15-pin (VGA) terminal on the projector. ¡Connect the monitor to this terminal using a monitor cable (not provided).

HDB15-PIN TERMINAL

5

4

3

 

2

1

10

 

9

8

7

6

15 14 13 12 11

Pin No./Signal

Pin No./Signal

1

Red input

9

Non Connect

2

Green input

10

Ground (Vert. sync.)

3

Blue input

11

Sense 0

4

Sense 2

12

Sense 1

5

Ground (Horiz. sync.)

13

Horiz. sync.

6

Ground (Red)

14

Vert. sync.

7

Ground (Green)

15

Reserved

8

Ground (Blue)

 

 

CONNECTING TO THE COMPUTER AUDIO INPUT JACKS (1 and 2)

¡Connect audio outputs from your computer to these jacks using the audio cable (not provided).

CONNECTING TO THE MULTI-POLE 12-PIN (CONTROL PORT) CONNECTORS (1 and 2)

¡If you wish to control the computer with projector’s remote control unit, you must connect the control port on your computer to the projector’s control port with the control cable for PS/2 port (provided).

 

 

 

 

PS/2-port

Serial Port

ADB Port

■ CONTROL PORT

 

1

––––––––

TxD

––––––––

 

 

 

5 2

1 4

 

2

CLK

––––––––

ADB

3

3

DATA

––––––––

––––––––

6

 

4

––––––––

––––––––

––––––––

 

 

 

 

 

 

5

––––––––

*RxD

––––––––

 

 

 

6

––––––––

––––––––

––––––––

 

 

 

7

––––––––

READY

––––––––

10

 

 

8

––––––––

––––––––

––––––––

11 8

7

9

GND

GND

GND

9 12

10

––––––––

––––––––

––––––––

 

 

 

11

––––––––

––––––––

––––––––

 

 

 

12

––––––––

––––––––

––––––––

CONTROL PORT CABLE REMOVAL HINT Disconnect control port cable with following steps.

1.

Hold the portion (A) of the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

connector with one hand.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

2.

Pull the portion (B) arrow

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

direction and remove

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

connector.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*NOTE: The RxD port (5 pin on the Serial Port) is provided on control port 2 connector only. If you control the projector by computer, you must connect control port 2 connector.

– 10 –