APPENDIX

 

 

 

 

 

 

Indicators

 

 

 

Projector Condition

 

 

LAMP

 

WARNING

 

READY

LAMP

 

 

 

 

REPLACE

 

TEMP.

 

 

 

 

 

 

 

 

 

green

red

 

 

 

 

 

 

yellow

 

red

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The projector is being cooled down. It cannot be turned on until

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the READY indicator lights green.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The projector detects an abnormal condition and cannot be

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

turned on. Unplug the AC Power Cord and plug it again to turn

 

 

 

 

 

 

 

 

 

 

 

 

 

 

on the projector. If the projector is turned off again, disconnect

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the AC Power Cord and contact the dealer or the service center

 

 

 

 

 

 

 

 

 

 

 

 

 

 

for service and checkup. Do not leave the projector on. It may

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cause electric shock or a fire hazard.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The projector is in the Power management mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The temperature inside the projector is abnormally high.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The temperature inside the projector is abnormally high. The projector cannot be turned on. When the projector is cooled down

enough and the temperature returns to normal, the READY indicator lights green and the projector can be turned on.

The lamp cannot light up. (The projector is preparing for standby or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed.)

The lamp cannot light up. (The lamp has been cooled down enough and the projector is in stand-by mode and ready to be turned on with the POWER ON-OFF button.)

The life of the projection lamp draws to an end.

Replace the lamp and then reset the Lamp time. The indicator will turn off.

• • • on

• • • flashing

• • • dim

• • • off

When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the Lamp Replace Counter after replacement of the lamp.

54