Sanyo SAP-C12AP, SAP-C18AP, SAP-C25AP, SAP-C30AP, SAP-C9AP, SAP-K12AP, SAP-K18AP, SAP-K25AP, SAP-K30AP 4.3 Using the General Operation

10

4.3 Using the General Operation

Press the setting buttons as described below and change the settings

as desired.

To STOP the air conditioner, press the ON/OFF operation button again.

STEP 2

STEP 1

STEP 4 STEP 5

STEP 3

STEP 1

STEP 3

STEP 4

STEP 5

To start the air conditioner, press the ON/OFF operation button.

Press the TEMP. setting buttons to change the temperature setting

to the desired temperature.

Adjustable temperature range:

30 °C (86 °F) max.—16 °C (61 °F) min.

Under “AUTO” operation, the temperature can not be adjust.

Under other operation, the initial value is 25 °C (77 °F).

Set the FAN SPEED selector button to the setting you want.

Press the

automatically

button and set the air blow direction as desired or

.

AUTO

: Auto fan speed.

: High fan speed.

: Middle fan speed.

: Low fan speed.

Under Dry mode, the fan speed is automatically set to LOW.

STEP 2 Press the MODE selector button and select the desired mode.

For DRY operation

For COOLING operation

For FAN only operation

For AUTO operation

For HEATING operation (Not function for cooling only model)

NOTE

NOTE

4. OPERATION OF WIRELESS REMOTE CONTROL UNIT

Operation and Maintenance

Contents

Main INSTRUCTION MANUAL SAMS ONLY 85S-6-4181-007-00-0 EXPLANATORY BOOKLET Page 1 Instruction Manual Features Features Contents Alert Symbols Operation and Maintenance Installation Service Product Information 1. NOTICES FOR OPERATION 1. NOTICES FOR OPERATION 2. NOTICES FOR USER Principle: Anti-freezing Function: 2.1 Working Principle & Special Functions for Cooling 2.2 Working Temperature Range 3. NAMES AND FUCTIONS OF EACH PART Indoor Unit S Ru D AUTO Symbols ON OFF OPER 4.2 Remote Control Unit (Functions) 4.2 Remote Control Unit Functions (Continued) AUTO 4.3 Using the General Operation AUTO 4.4 Using the 24-Hour ON or OFF Timer 4.5 Using the SLEEP Operation 4.6 Using of the Special Features 4.6 Using of the Special Features (Continued) 4.7 How to Install Batteries o 4.9 Emergency Operation 4.8 Using the Remote Control Unit 5. CLEAN AND CARE 5.1 Clean the Front Panel (Make sure to take it off before cleaning) 5.2 Cleaning the Air Filters (Recommended once every 3 months) 5. CLEAN AND CARE 5.4 Maintain After Use 5.2 Cleaning the Air Filters (Continued) 5.3 Check Before You Use Page 6. TROUBLESHOOTING Remote control is not av ailable . I f w a t e r l e a k a g e i n i n d o o r u n i t . If water leakage in outdoor unit. 7. NOTICES FOR INSTALLATION 7.1 Basic Requirements for Installation Position 7.2 Indoor Unit Installation Position Selection 7.3 Outdoor Unit Installation Position Selection 7. NOTICES FOR INSTALLATION 7.4 Safety Requirements for Electric Appliances 7.5 Earthing Requirements 7.6 Others 7.3 Outdoor Unit Installation Position Selection (Continued) 8. INSTALLATION DIENSION DIAGRAM Space to the ceiling Space to the wall Space to the obstruction 9.1 Install the Rear Panel 9.2 Install the Piping Hole 9.3 Install the Water Drainage Pipe 9.4 Connect Indoor and Outdoor Electric Wire WARNING 24 9.4.2 Wire Length and Diameter Model: KC30AP WARNING Be sure to connect the power supply line to the indoor unit as shown in the wiring diagram. 9.5 How to Install the Indoor Unit 10.1 Wiring Instructions for the Outdoor Unit Wire clamp Power Connection Wire 10.2 Refrigerant Tubing IMPORTANT 10.3 Air Purging 10.3 Air Purging - (Continued) 31 Table 5 listed the accessories supplied with the unit. 10.4 Tubing Length C9AP 5.0 520 C12AP 5.0 520 30 C30AP 5.0 15 50 11. PUMP DOWN 11.1 What is Pump Down? 11.2 Pump Down Procedure 12. CHECK AFTER INSTALLATION AND TEST RUN 12.1 Check After Installation 12.2 Test Operation 34 13.1 What is self diagnosis function? 13. SELF DIAGNOSIS FUNCTION Fig. 42 Table 6a