Saris 801 manual Load and Secure Bikes Final Adjustment, Check Straps &STABILITY, Warranty, 12-15

3	LOAD AND SECURE BIKES:		4	FINAL ADJUSTMENT
	• Place bikes on carrier arms in bike supports, alternating direction of handlebars.				•Retighten mounting straps with bicycles on carrier, then tie off (Fig 11).
		Pull hold-down strap snug against bike tube. Rest seat tube against stabilizer			•In unique cases, the stabilizer strap will not be long enough to secure
		and pull strap around tube as shown in Fig. 7.			the seat tube. If this occurs, please call Saris at 1-800-783-7257 for an
	• If pedal touches vehicle, rotate arms up.				additional stabilizer strap #12398.
	• To release hold-down straps, follow Fig. 8.
					Figure 11	Figure 12
	• Women’s frames can be mounted as shown in Fig. 9.

Figure 7a	Figure 8
CAUTION:
Pulling up on hold-down
strap could cause failure
Figure 7

Figure 9 Figure 10

12-15”

•Check clearance. It is the responsibility of the user to ensure the necessary clearance (dependent on vehicle, load, driving territory, etc.) is given from load to ground. Generally, 12-15” is adequate (Fig. 10). If necessary, rotate arms up until at least 12-15” of clearance is achieved.

CAUTIONS:

Tie off all straps.

Rethreading Straps

5 CHECK STRAPS &STABILITY

While in use, recheck your installation •During first use check after 30 minutes or 30 miles. •Thereafter, check every 200 miles.

•Check more frequently on bumpy roads.

•If bicycles shift or move, check IMMEDIATELY.

Be sure all straps are taut and knotted firmly against buckles.

1)All requirements for compatability/fit as stated in the current Saris vehicle/carrier compatability guide must be followed. (Available at any Saris dealer). If your vehicle is not listed or you have any questions, please call our customer service at 800-783-7257.

2)Bones is a bumper-supported bike rack. Bumper legs must rest on bumper.

3)Bones is not intended for use with tandem or recumbent bicycles.

4)Read and follow instructions carefully. Save owner’s manual for future reference or parts information.

5)Replace any mounting strap at the first sign of wear. Replacement parts are available through your local Saris dealer or call 1-800-783-7257.

6)S-hook straps must be parallel with the rear leg to prevent shifting.

7)Make sure bike tires are not directly behind exhaust pipe.

8)Never place more than three bicycles (maximum weight 105 lbs) on carrier. Secure properly and adjust for even load distribution.

9)Do not mount to any type of trailer.

10)No part of carrier, including straps, should ever come in contact with spoiler.

11)Do not open rear deck (trunk) with carrier installed.

12)This carrier is not recommended for off-road use or for use at speed exceeding 65 mph.

13)Remove carrier from vehicle when not in use.

14)When cleaning rack, use only water soluble cleaners.

15)Rear window wipers may not be usable while carrier is attached to vehicle.

16)It’s the end users responsibility to ensure that use of this product meets all local and state laws.

17)To prevent potential damage, secure the front tires of bicycles (part number 3033 recommended).

WARNING AND DISCLAIMER:

This carrier has been designed to carry bicycles on specific vehicles. Before installation, user must read and follow current Vehicle/ Carrier Compatibility Guide (available through Saris dealer) recommendations and enclosed instructions. Fit recommendations are based on vehicle's standard features; optional features may affect the fit recommendations. User must attach carrier correctly to the vehicle, check its attachment before each use, and inspect carrier parts for wear. Carrier's attachment to the vehicle is critical and beyond the control of the manufacturer. Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, or neglect of this carrier.

WARRANTY:

We warrant this product to the first consumer to be free from defect in material and workmanship for the lifetime of the product. Any product or part thereof found to be defective will be replaced without charge provided that: (1) the product was not misused; (2) no alterations or modifications were made; (3) its failure resulted from a defect in material or workmanship and not from normal wear expected in the use of the product; (4) the product or part is delivered, freight prepaid, to Graber Products. Manufacturers only obligation shall be to replace such products or parts proved to be defective. Please contact Graber at the number below prior to return to obtain a return authorization number.

	5253 Verona Road
Made in U.S.A.	Madison, WI 53711	U.S. Patent
	1-800-783-7257
10690 Rev. G 02/01	www.sarisproducts.com	#5,495,970