Reverse Travel | Scag Power Equipment STC52V-27CV-SS guide

Section 4

R

Reverse Travel

Caution

Disengage power to the mower before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower.

4.6ENGAGING THE DECK DRIVE (CUTTER BLADES)

1.Set the throttle at about 3/4 speed. Do not attempt to engage the deck drive at high speed as this shortens the electric clutch life — use only moderate engine speed when engaging the deck drive.

2.Engage the deck drive by pulling out on the yellow switch, located on the instrument panel, to the engage position. See Figure 4-3.

Caution

Before backing up, observe the rear for persons and obstructions. Clear the area before backing up. Possible injury or property damage could occur.

To travel in reverse, pull levers inward out of the neutral lock position and pull both handles back. Keep the travel speed low while traveling in reverse.

- NOTE -

The mower may not travel straight in reverse. Slight adjustments may need to be made using the steering controls.

To steer left while traveling in reverse, allow the left steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower will turn left.

To steer right while traveling in reverse, allow the right steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower will turn right.

To stop the reverse travel, allow the steering control levers to return to the neutral position. If the mower is to be parked, place the handles in the neutral lock position and engage the parking brake.

PULL UP TO ENGAGE

PUSH DOWN TO DISENGAGE

390S0138

Figure 4-3. Cutter Engage Switch

- NOTE -

A squealing noise may be heard when engaging or disengaging the deck drive. It is caused by the electric clutch plates meshing as the mower comes up to speed. This is normal.

3.To disengage the deck drive, push the switch in to the disengage position.

4.Always operate the engine at full throttle to properly maintain cutting speed. If the engine starts to lug down, reduce the forward speed and allow the engine to operate at maximum RPM.

15

Image 19

Scag Power Equipment STC52V-27CV-SS manual Engaging the Deck Drive Cutter Blades, Reverse Travel

Contents

OPERATOR’S Manual STC48V-19KAI Remember Your Mower is only AS Safe AS the OperatorSTC52V-27CV-SS Table of Contents Following Section Limited Warranty Commercial Equipment Direction Reference USE only Scag Approved Attachments and AccessoriesGeneral Information Introduction Symbol Description SymbolsSTT Models Signal Word Safety InformationSignal Words This symbol means Attention! Become Alert! Your Operation Considerations Section Foldable Roll-Over Protection System Roll-over protection system Seat Belt Inspection Using a spark arrestor Maintenance Considerations & storage Install Belt COvER Before Safety and Instructional Decals Electrical EngineTractor Productivity Weights and Dimensions 48V 52V 61VCutter Deck Hydraulic System Controls and Instrument Identification Operating Instructions Initial RUN-IN Procedures Safety Interlock SystemFirst Day of Use or Approximately 20 Hours Ground Travel and Steering Starting the EngineForward Travel Reverse Travel Engaging the Deck Drive Cutter Blades After Operation Rotating BladesHillside Operation Parking the Mower Moving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Deck Release Lever Towing optional hitch accessory Condition Cause Cure Troubleshooting Cutting Conditions Troubleshooting Cutting Conditions Contd Cutting path Scalping Blades HittingDirt or CuttingVery Close To the Ground Step Cut Ridge in Center Parking Brake Adjustment AdjustmentsTravel Adjustments Tracking Adjustment Neutral Adjustment Belt Alignment Throttle Control and Choke AdjustmentsBelt Adjustment Cutter Deck Adjustments Cutter Deck Pitch Cutter Deck Height Cutter Deck Height Adjustment Position Custom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment Clutch Air Gap Adjustment Electric clutch adjustment Hours MaintenanceMaintenance Chart Recommended Service Intervals Procedure Comments Break-In 100 200 500 First Location Lubrication Interval Lubricant NO. Places Lubrication Lubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil Level Engine Fuel System Engine Oil Cleaning and/or Replacing Air Cleaner Element Engine Air CleanerReplacing In-Line Fuel Filter Elements Jump Starting BatteryCharging the Battery Battery Electrolyte First AID Blade Inspection Blade ReplacementDrive Belts Cutter Blades BODY, DECK, and Upholstery Tires Scag Approved Attachments and Accessories Illustrated Parts List 48V & 52V Cutter Decks Description 61V Cutter Deck 424367 Dust Shield 483210 Idler Pulley, 5 Dia Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 482619 Tire, 13 x 6.5-6 Smooth 483736 STC Foldable ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System STC Suspension Seat Section Drive System Components 04019-04 Nut, Serr. Flange 3/8-16 04001-136 Engine & Attaching Parts Section Steering Components Damper orange colored print Damper blue colored print Brake Components Brake Components HYDRO-GEAR Parker Wheel Motor Part Number Identification Section 33 47 Fuel and Hydraulic System Electrical System Battery, 350CCA Not Available Through Scag BDP-10A Hydraulic Pump Assembly Housing Kit Manufactured Under ONE or More Replacement Decals and Information Plates 482166R STC 2009 RDP2 PTO Switch Diode KEY Electrical Schematic Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Está mientras equipo del parte ninguna lave No RecauciónP Corte de cuchillas con trabajar al ojos y CuchillaNota Cuchilla la de Reemplazo .8-7 Figura Nota Afilado.B Transmisión DE CorreasRranB Electrolito Para Auxilios Primeros 7aterBater Deaíla Bater DE Motor Aire del Iltro7 Motor Ceite7 MotorCombustiblede Istema5.7del Hidráulico aceite de Depósito .2-7 Figura Hidrulicoá S istema3.7Aceite hidrulicoCáambio.B Aceite De nivel Hidrulicoá ErificarV.A Conexión de puntos de Lubricación .1-7 Figura Horas Ubicaciones Lubricante Lubricación UbicaciónDE Intervalo Observaciones Procedimiento Observaciones Procedimiento Primeros Inicial USO Horas Sección Corte de plataforma la de Tope .7-6 Figura Personalizado a 7juste.6ctorl Corte de plataforma la de altura de Ajuste .6-6 Figura Corte de plataforma la de nivel del Ajuste .5-6 Figura Advertencia Control de varilla la de Ajuste .3-6 Figura Dirección de Ajustes Solución Causa Condición Coninuaciónt ID E Enganche cional Remolque14.4orio Descarga de válvula de Control .4-4 Figure Corte DE Altura LA DE Ajuste Peligro RecauciónP Precaución Descarga de válvula de Control .2-4 Figure Inicial Arranque DE Procedimientos Interruptor El .1-4 Figura encendido de Interruptor Instrumentos e Controles .1-4 Figure 61V 52V 48V PRO Especificaciones SE DE Yuridadas G Instructi CALCOMANÍAS.27 Ertenciaadv Almacenamiento mantenimiento Ertenciaad Rops del Bisagra .2-2 Figura Seguridad de cinturón del Inspección .3-2 FiguraVuelco contra protección de Sistema .1-2 Figura Protecciónde Uelcov POR Aprobadas Operaciones LAS CON Osha De freno el desconectada, esté plataforma de Defectuosamente Funcionando ni desconectado bloqueo deNo estacionamiento de freno el y neutral la de Diferente posición una en dirección de control Ridadg SE DEInformación Señalización DE Palabras Descripción Símbolo STT Scag POR Aprobados Dispositivos USE Sólo General InformaciónInstrucciones DE REFERENCIA12 INTRODUCCIÓN11 Stali GarantManten Ridad Advertencia Operador DEL Manual