Custom Cut Baffle | Scag Power Equipment STT-31BSG guide

Section 6

To adjust the Custom-Cut Baffle height:

1.Place the cutter deck in the transport position.

2.Remove the hardware securing the Custom-Cut Baffle to the cutter deck. (See Figure 6.8).

-NOTE-

Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on cutter deck size.

MOUNTING MOUNTING

HARDWAREHARDWARE

2002 CCB

Figure 6-8. Custom Cut Baffle

3.Move the Custom-Cut Baffle to desired position. (See Figures 6.9 through 6.11 for position).

4.Reinstall the mounting hardware as shown. (See Figures 6.10 though 6.11). Torque hardware to 39ft.lbs.

2002 CCB - 3" Setting

Figure 6-9. 3" Custom Cut Baffle Position

CARRIAGE BOLT

		2002 CCB - 3-1/2" Setting
BOTTOM SET OF HOLES	FLATWASHER	ELASTIC STOP
FOR 3-1/2" SETTING		NUT

Figure 6-10. 3-1/2" Custom Cut Baffle Position

CARRIAGE BOLT

		2002 CCB - 4" Setting
TOP SET OF HOLES	FLATWASHER	ELASTIC STOP
TOP SET OF HOLES		NUT
FOR 4" SETTING		NUT
FOR 4" SETTING

Figure 6-11. 4" Custom Cut Baffle Position

25

Image 29

Scag Power Equipment STT-31BSG manual Custom Cut Baffle

Contents

OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Introduction General InformationDirection Reference Servicing the Engine and Drive Train Components ISO Symbols CE Mark Fast Slow Before Operation Considerations Safety Information Operation Considerations Before Operation Considerations Contd Operation Considerations Contd Maintenance Considerations Safety and Instructional Decals Drive System EngineEngine Deck Additional Specifications SpecificationsApproximate Dimensions Productivity Controls and Instrument Identification Operating Instructions Dump Valve Control Safety Interlock System Forward Travel Starting the EngineGround Travel and Steering Engaging the Deck Drive Cutter Blades Reverse Travel After Operation Hillside OperationParking the Mower Recommendations for Mowing Removing Clogged MaterialMoving Mower with Engine Stopped Towing optional hitch accessory Adjusting Cutting Height Condition Cause Cure Troubleshooting Cutting Conditions Scalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause Cure Ground Troubleshooting Contd Travel Adjustments AdjustmentsParking Brake Adjustment RH Steering Control Rod Adjustment Neutral Adjustment Throttle Control and Choke Adjustments Tracking AdjustmentBelt Adjustment Belt Alignment Cutter Deck Pitch Cutter Deck AdjustmentsCutter Deck Level Cutter Deck Height Custom-Cut Baffle Adjustment Custom Cut Baffle Maintenance Chart Recommended Service Intervals Maintenance Lubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals Contd Lubrication Fitting Points Changing Hydraulic Oil Hydraulic SystemChecking Hydraulic Oil Level Changing Hydraulic Oil Filter Element Engine OILChecking Engine Crankcase Oil Level Changing Engine Crankcase Oil Engine Fuel System Engine AIR CleanerBattery Battery Electrolyte First AID Charging the Battery Drive Belts Jump StartingCutter Blades Blade Inspection Tires Blade Replacement Checking Lubricant Level Cutter Deck GearboxCooling System Checking Coolant Level BODY, DECK, and Upholstery Cleaning the Radiator Debris ScreenChecking The Fan Belt Tension Page 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Wheel Assy Inc.items 20, 42, 43, 54 Deck Drive Components Ref. Part Description RADIATOR, Coolers & Engine Brackets Ref. Part No. No. Description Brake and Steering Components Part Description Fuel and Hydraulic System Ref. Part Description Electrical System Ref. Part No. No. Description Hydraulic Pump Assembly BDP-21L Housing Kit Includes Housing, Journal Bearing Wire HARNESS, STT 31BSG Part Number Heavy-Duty 48825 48314 481937 Limited Warranty Commercial Equipment 2002