Section 7

R

A. Charging the Battery

Refer to the battery charger’s manual for specific instructions.

Under normal conditions the engine’s alternator will have no problem keeping a charge on the battery. If the battery has been completely discharged for a long period of time, the alternator may not be able to recharge the battery, and a battery charger will be required.

DO NOT charge a frozen battery. It may explode and cause injury. Let the battery warm before attaching a charger.

Whenever possible, remove the battery from the mower before charging and make sure the electrolyte covers the plates in all cells.

WARNING

BATTERIES PRODUCE EXPLOSIVE GASES. Charge the battery in a well ventilated space so gases produced while charging can dissipate.

Charging rates between 3 and 50 amperes are satisfactory if excessive gassing or spewing of electrolyte does not occur or the battery does not feel excessively hot (over 125°F). If spewing or gassing occurs or the temperature exceeds 125°F, the charging rate must be reduced or temporarily stopped to permit cooling.

B. Jump Starting

1.The booster battery must be a 12 volt type. If a vehicle is used for jump starting, it must have a negative ground system.

2.When connecting the jumper cables, connect the positive cable to the positive battery post, then connect the negative cable to the negative battery post.

7.8 Drive Belts

All drive belts are spring-loaded and self-tensioning, however after the first 2, 4, 8 and 10 hours of operation, the belts should be checked for proper alignment and wear. Thereafter, check the belts after every 40 hours of operation or weekly, whichever occurs first.

- NOTE -

If you experience frequent belt wear or breakage, see your authorized Scag service center for belt adjustment.

7.9 Cutter Blades

A. Blade Inspection

1.Remove the ignition key before servicing the blades.

2.Raise the mower deck to the highest position. Place the lanyard pin in the highest cutting height position to prevent the cutter deck from falling.

WARNING

Always wear proper hand and eye protection when working with cutter blades.

3.Check the cutter blades for straightness. If the cutter blades appear bent, they will need to be replaced.

WARNING

Do not attempt to straighten a bent blade, and never weld a broken or cracked blade. Always replace it with a new blade to assure safety.

4.If a blade cutting edge is dull or nicked, it should be sharpened. Remove the blades for sharpening. See "Blade Replacement."

- NOTE -

Keep the blades sharp. Cutting with dull blades not only yields a poor mowing job, but slows the cutting speed of the mower and causes extra wear on the engine and the blade drive by pulling hard.

B. Blade Sharpening

- NOTE -

If possible, use a file to sharpen the blade. Using a wheel grinder may burn the blade.

37

Page 40 Page 42
Page 41
Image 41
Scag Power Equipment STT61V-31KB-DF manual Drive Belts, Cutter Blades
Page 40 Page 42

STT61V-31KB-DF specifications

The Scag Power Equipment STT61V-31KB-DF is a remarkable addition to the lineup of professional-grade mowers, tailored for those who require unmatched performance and durability. This zero-turn mower is designed with landscapers and lawn care professionals in mind, featuring cutting-edge technology and robust characteristics that elevate its functionality in various environments.

At the heart of the STT61V-31KB-DF is a powerful 31-horsepower Kawasaki engine. Renowned for its reliability and efficiency, this engine provides ample power, ensuring that even the most demanding tasks can be tackled with ease. This mower employs a dual-fuel capability, enabling operators to switch between gasoline and propane, thereby enhancing versatility and fuel consumption efficiency. This feature is particularly favorable for those looking to manage costs while maintaining high productivity.

One of the standout characteristics of the STT61V-31KB-DF is its 61-inch Velocity Plus cutting deck. The design of this deck allows for superior airflow, resulting in a clean cut even in tall grass. The adjustable cutting height ranges from 1 to 5 inches, giving users the flexibility to achieve the desired look for any lawn. The reinforced edges and heavy-duty construction ensure durability, enabling the mower to withstand the rigors of frequent use.

Another highlight is the innovative suspension system, which contributes to a smooth ride over uneven terrain. The adjustable anti-scalp rollers prevent lawn damage, ensuring that the mower glides effortlessly, maintaining high-quality cutting results. The ergonomic design of the operator controls allows users to navigate with ease, enhancing overall comfort during extended mowing sessions.

The machine is equipped with professional-grade wheels and a heavy-duty frame, providing stability and traction on various surfaces. Additionally, the intuitive dashboard incorporates easy-to-read gauges and controls, enabling operators to monitor performance and adjust settings instantly.

The Scag Power Equipment STT61V-31KB-DF exemplifies robust engineering, with a focus on performance, comfort, and durability. For those in the landscaping business or serious lawn enthusiasts, this mower stands out as a reliable companion that facilitates efficient and effective lawn care operations, making it a worthy investment.
Top Page Image Contents