Schneider Electric MNA01M001EN

PC/-PA/+

PC/-

PA/+

Part Length in mm (inches)

A Cable jacket 130 (5.2)

B Length of shield connection 60 (2.5)

C Stripping length 6 (0.25)

Diameter ring-type cable lug /

fork-type cable lug

For M5 screw

▶(1) Strip the cable jacket, length A.

▶(2) Slide back the shield braiding. Open the shield braiding and

twist it to form a shield connection wire.

▶(3) Shorten the twisted shield connection wire to length B and insu-

late the shield braiding with heat shrink tube.

Crimp the crimp contacts to the two stripped conductors. The strip-

ping length is C. See chapter "6.1 DC bus accessories", page 55

for information on the crimping tool.

▶(4) Crimp a fork-type cable lug to the shield connection wire.

Push the crimp contacts into the connector housing. Polarity: the

red wire is PA/+, the black wire is PC/-.

▶(5) Secure the shield with heat shrink tube.

LXM32 4 Installation

Common DC bus 43

MNA01M001EN, V1.01, 08.2014

Contents

Main LXM32 Table of contents LXM32 Table of contents Table of contents LXM32 Safety Information Hazard categories DANGER WARNING CAUTION Qualification of personnel Intended use Safety Information LXM32 Basic information DANGER Safety Information LXM32 DC bus voltage measurement DANGER Standards and terminology Page About the book LXM32 About the book Page 1 Introduction LXM32 1 Introduction 1.1 Permissible device types for common DC bus 1 Introduction LXM32 2 Technical Data 2.1 Firmware version 2.2 DC bus data Single-phase drives Three-phase drives 16 Common DC bus 2.3 Braking resistor Common DC bus 17 Three-phase drives 18 Common DC bus 2.3.1 External braking resistors (accessories) Common DC bus 19 2.4 Cables for the DC bus 3 Engineering 3.1 Energy balance 3.1.1 Energy balance basics v D I t 3.2 Electromagnetic compatibility (EMC) 3.4 Fuses 3.4.1 DC bus connection of single-phase drives Page 3.4.2 DC bus connection of three-phase drives Page 3.4.3 Supply via the DC bus Page ~ 3.5 Braking resistors 3.5.1 Rating the braking resistor WARNING 3 Engineering LXM32 Page 3.5.2 Rating information Page 3.6 Mains reactor See the manual of the respective product for information on mains reactors. Common DC bus 37 3.7 Mains filter 3.8 Mains reactor and external mains filter Common DC bus 39 Page 4 Installation Figure 14: Specifications for drives with mains supply 4.1 Assembling cables 42 Common DC bus Page Page 4.2 Wiring the DC bus 4.2.1 Drives with connectors Page 4.2.2 Drives with terminals CN9 4.2.3 Connecting the DC bus 4.3 Verifying installation Page 5 Commissioning LXM32 5 Commissioning 5.1 Commissioning procedure 5.1.1 DC bus connection LXM32 to LXM32 5 Commissioning LXM32 5.1.2 Supply via the DC bus LXM32 5 Commissioning 5.2 LXM32: Setting the braking resistor parameters WARNING 5 Commissioning LXM32 6 Accessories and spare parts 6.1 DC bus accessories 6.2 DC fuses LXM32 6 Accessories and spare parts 6.3 External braking resistors 6 Accessories and spare parts LXM32 Glossary Units and conversion tables Length Mass Force Glossary LXM32 Terms and Abbreviations LXM32 Glossary Page Table of figures LXM32 Table of figures Page Index LXM32 Index Index LXM32