Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST160LT009 - 9WC14D, ST160LT011 - 9ZVG4D, ST160LT007 - 9ZV14D, ST160LT014 - 9YK14D manual

Models: ST250LT014 - 9YK14C ST160LT011 - 9ZVG4D ST320LT007 - 9ZV142 ST160LT014 - 9YK14D ST160LT007 - 9ZV14D ST320LT011 - 9ZVG42 ST160LT009 - 9WC14D ST250LT011 - 9ZVG4C ST320LT014 - 9YK142 ST250LT007 - 9ZV14C ST320LT009 - 9WC142 ST250LT009 - 9WC14C

1 46

Download 46 pages 18.79 Kb

Page 26

Image 26

Measurements shown in Figures 4 and 5 are in inches.

Figure 4. Mounting dimensions (for FIPS 140-2 models) — top, side and end view

Warning: FIPS 140-2 Models Contain 3 Tamper Evident Stickers with the marking "Tamper Indicator - Do Not Remove". These stickers must remain attached to provide the tamper evidence throughout the life of the drive. Removing these stickers will indicate tampering and void the drive warranty.

20	Momentus Thin Product Manual, Rev. C Gen-2

Page 26

Image 26

Seagate ST160LT009 - 9WC14D, ST160LT011 - 9ZVG4D, ST160LT007 - 9ZV14D, ST160LT014 - 9YK14D, ST250LT007 - 9ZV14C manual

Contents

ST model # ST model #Momentus Thin Revision history 3.0 Drive specifications Contents1.0 Seagate Technology support services 2.0 Introduction 4.0 Configuring and mounting the driveMomentus Thin Product Manual, Rev. C Gen-2 List of Figures Page 1.0 Seagate Technology support services SEAGATE ONLINE SUPPORT and SERVICES2.0 Introduction 2.1 About the Serial ATA interface Drive specifications 3.0 Drive specifications3.1 Specification summary table Drive specifications Supports Hotplug operation per Serial ATALBA mode 3.3 Default logical geometry3.2.1 LBA mode 3.2 Formatted capacity3.7 Seek time 3.6 Physical characteristics3.5 Recording and interface technology Table 2 Typical seek timesSeek mode 3.9.1 Power consumptionSpinup power Read/write power and currentMomentus Thin Product Manual, Rev. C Gen-2 power to operational levelsStandby power is measured at steady state after 200ms from transition 3.9.3 Conducted noise 3.9.1.1 Typical current profile3.9.2 Deferred spinup 3.9.4 Voltage toleranceActive mode 3.9.5 Power-management modesPower management modes Idle mode3.10.3.2 Wet bulb temperature 3.10.1 Ambient temperature3.10.2 Temperature gradient 3.10.3 Humidity 3.10.3.1 Relative humidity3.10.5.2 Nonoperating shock 3.10.5 Shock3.10.5.1 Operating shock 3.10.6 Vibration3.12 Electromagnetic immunity Table 5 Drive A-weighted Sound Power Levels SWL, BA3.11 Acoustics Test for Prominent Discrete Tones PDTsReliability 3.14.1 Safety certification3.13 3.14 Agency certificationAustralian C-Tick N176 3.14.3 FCC verification3.15.1 European Union Restriction of Hazardous Substances RoHS 3.15 Environmental protection3.16 Corrosive environment 3.15.2 China Restriction of Hazardous Substances RoHS Directive4.2 Configuring the drive 4.0 Configuring and mounting the drive4.1 Handling and static-discharge precautions Figure 3. Attaching SATA cabling 4.3 Serial ATA cables and connectors4.4 Drive mounting Top cover stiffness/deflectionPage Momentus Thin Product Manual, Rev. C Gen-2 Level 2 security 5.0 About FIPSPurpose Note. May not represent actual drive Momentus Thin Product Manual, Rev. C Gen-2Serial ATA connector pin definitions 6.0 Serial ATA SATA interface6.2 Serial ATA device plug connector pin definitions 6.1 Hot-Plug compatibilitySegment Serial ATA connector pin definitionsPower Command code in hex 6.3 Supported ATA commandsCommand name ATA-standard commandsATA-standard power-management commands Command nameCommand code in hex ATA-standard security commandsDescription 6.3.1 Identify Device commandWord ValueValue WordDescription xxxxHValue WordDescription xxxxHWord 0 Ultra DMA mode 0 is supported 1 Ultra DMA mode 1 is supportedWord 6.3.2 Set Features command Table 8 Set Features command valuesCode in features register 6.3.3 S.M.A.R.T. commandsS.M.A.R.T. commands S.M.A.R.T. commandMomentus Thin Product Manual, Rev. C Gen-2 Index Page Page Momentus Thin Product Manual, Rev. C Gen-2 Page Seagate Technology LLC