Seagate ST3450856FC Inquiry data, Mode Sense data, Cheetah 15K.6 FC inquiry data Bytes Data hex

[3]Reference Mode Sense command 1Ah for mode pages supported.

[4]Y = Yes. Command is supported.

N = No. Command is not supported.

A = Support is available on special request.

9.3.1Inquiry data

Table 20 lists the Inquiry command data that the drive should return to the initiator per the format given in the Fibre Channel Interface Manual.

Table 20:	Cheetah 15K.6 FC inquiry data
Bytes	Data (hex)
0-15	00	00	xx**	12	8B	00	PP	0A	53	45	41	47	41	54	45	20	Vendor ID
16-31	[53	54	33	34	35	30	38	35	36	46	43]1	20	20	20	20	20	Product ID
32-47	R#	R#	R#	R#	S#	S#	S#	S#	S#	S#	S#	S#	00	00	00	00
48-63	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00
64-79	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00
80-95	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00
96-111	00	43	6F	70	79	72	69	67	68	74	20	28	63	29	20	32*	*Copyright
112-127	30*	30*	37*	20	53	65	61	67	61	74	65	20	41	6C	6C	20	notice
128-143	72	69	67	68	74	73	20	72	65	73	65	72	76	65	64	20

*Copyright year (changes with actual year).

**SCSI Revision support. Refer to the SPC release documentation for definitions.

PP50 = Inquiry data for an Inquiry command received on Port A. 70 = Inquiry data for an Inquiry command received on Port B.

R#	Four ASCII digits representing the last four digits of the product firmware release number.
S#	Eight ASCII digits representing the eight digits of the product serial number.
[ ]	Bytes 18 through 26 reflect model of drive. The table above shows the hex values for Model ST3450856FC.
	Refer to the values below for the values of bytes 18 through 26 of you particular model:
	ST3450056FC	53	54	33	34	35	30	30	35	36	46	43
	ST3300656FC	53	54	33	33	30	30	36	35	36	46	43
	ST3300056FC	53	54	33	33	30	30	30	35	36	46	43
	ST3146356FC	53	54	33	31	34	36	33	35	36	46	43
	ST3146756FC	53	54	33	31	34	36	37	35	36	46	43

9.3.2Mode Sense data

The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The drive maintains four sets of mode parameters:

1.Default values

Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the drive’s PCB. These default values can be changed only by downloading a complete set of new firmware into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use those in a Mode Select command to set up new current and saved values, where the values are change- able.

2.Saved values

Saved values are stored on the drive’s media using a Mode Select command. Only parameter values that are allowed to be changed can be changed by this method. Parameters in the saved values list that are not changeable by the Mode Select command get their values from default values storage.

62 Cheetah 15K.6 FC Product Manual, Rev. D