Sears 113.23611 manual AdditionaJ safety instructions for scroll saw, Vingarea

additionaJ safety instructions for scroll saw

Safety is a combination of operator common sense and altert-

ness at all times when the scroll saw is being used,

WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT TO OPERATE YOUR SCROLL St_'UNTIL IT IS COMPLETELY ASSEMBLED AND iNSTALLED ACCORDING TO THE

INSTRUCTIONS...AND UNTIL YOU READ AND UNDER. STAND THE FOLLOWING:

			Page
1.	General Safety Instructions	for Power Tools	2
2.	Assembly		6
3.	Getting To Know Your Scroll	Saw	12
4.	Basic Scroll Saw Operation	...................	14
5.	Maintenance		16

6.Stability of Machine.

Your scroll saw must be bolted securely to stand or work

bench, In addition, if there is any tendency for the scroll saw to move during certain operations, bolt your scrollsaw stand or workbench to the floor.

7.Location

This scroll saw is intended for indoor use only.

8.Protection: Eyes, Hands, Face, Ears, Body

A.To avoid being pulled into the blade:

1.Roll long sleeves above elbows

2.Do not wear:

a.Gloves

b.Jewelry

c.Ties or other loose clothing

3.Tie back long hair

B.Do not cut pieces of material too small to hold by hand outside the blade guard.

C.Avoid awkward hand positions where a sudden slip could cause a hand to move into the blade.

D.To avoid slips due to lifting of the work piece make sure the blade teeth point downward toward the table.

E.To avoid blade breakage always adjust blade tension correctly.

F.To avoid losing control of the work piece or tool:

1.When cutting a large piece of material make sure it is fully supported at table height.

2.Hold the work piece firmly against the table.

3.Do notfeed the material too fast while cutting. Only feed the material fast enough so that the blade will cut.

4.Use caution when cutting off material which is irregular in cross section which could pinch the blade before the cut is completed. A piece of moiding, for

example, must ray flat on the table and not be per- mitted to rock while being cut.

5.Use caution when cutting off round material such as dowel rods, or tubing. They have a tendency to roll while being cut causing the blade to bite. Use a V- block to control the piece.

G.When backing the blade out of the workpiece, the blade may bind in the kerf (cut).,.this is usually caused by sawdust clogging up the kerf. If this happens: Turn off the scroll saw.. . remove plug from power source outlet...wedge open the kerr.., back the blade out of the workpiece.

H.To avoid unsupervised work, use or accidents due to inattention:

t.Never leave the scroll saw work area with the power on, before the machine has come to a complete stop, or without removing and storing the switch key.

2.Do not perform layout, assembly or set up work on the table while the cutting tool is in operation.

3.Turn saw "OFF" and remove plug from power supply outlet before installing or removing an accessory attachment.

4.Never turn your scrolt saw "ON" before clearing the table of all objects: (tools, scraps of wood, etc.) except for the work piece and related feed or support devices for the operation planned.

9.Should any part of this scroll saw be missing, bent, or fail in any way, or any electrical component fail to perform properly, shut off power switch and remove plug from power supply outlet. Replace damaged, missing, and/or failed parts before resuming operation.

10.Think Safety.

Safety is a combination of operator common sense and alertness whenever the scroll saw is in operation.

WEAR YOUR

The operation of any power tool can resuit in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety goggles complying with ANSI Z87.1 (shown on Package) before commencing power tool operation. Safety goggles are available at Sears retail or catalog stores.

i DANGER ! _o,YouownSAF_'_-_._	o._.
manu_ bek_'eoparat_j Sc_t Saw.
t. ALWAYS wear SAFETY GOGGLES complying with ANSi 7.87.!.
3. Turn saw Off and REMOVE SW]TCH KEY before ad_ saw, ch_	blade, or
_vingarea.

4. When INSTALLING BLADE: Blade teeth must a_ays point down. Put tension on blade

I_ turr_	kno_	(at rear) dook_se	or_ _1t _,_rnI_	t_,e,up of _,	F_	_
installal_	az_	ct'_YJng: procedure	inowner'smanual.			_\

Eiect_al: 120voWs

60 HZ AC 0_ty, 2,0 amps es,_4_=

I

J

WARNING: ALWAYS KEEP ALERT. DO NOT ALLOW FAMILIARITY (GAINED FROM FREQUENT USE OF YOUR SCROLL SAW) TO CAUSE A CARELESS MISTAKE. ALWAYS REMEMBER THAT A CARELESS FRACTION OF A SECOND IS SUFFICIENT TO iNFLICT SEVERE INJURY.