SERViCEA D ADJUST ENTS

TO REPLACE BELTS

The drive belts on this snow thrower are of special con-
struction and should be replaced withoriginal equipment
beetsavailable from your nearest SEARS Store or Serv-
ice Center.
You will need the assistance of a second person while
replacing the belts..
Drain the gasoline from thefuel tank byremoving the fuel
line.. Drain the gas and reinstall fuel line._
..........................,HI JULLU U,, ,I ,llllIII
!_ CAUTION'. DRAIN THE GASOLINE OUT i
DOORS, AWAY FROM FIRE OR FLAME.
J,,i .............
AUGER DRIVE BELT
if your snow thrower will not discharge snow, and the
auger drive belt is damaged, replace itas follows:
e Disconnect the spark plug wire.
eRemove the belt cover (See Fig.. 23)
e Loosen the right hand belt guide (See Fig. 26) and
pull away from the drive pulley.
e Loosen the auger idler pulley (See Fig..27) and pull
away from the belt.
eEngage the auger drive clutch lever.This will pullthe
brake assembly away from the pulley and allow the
belt to be slipped ouL
e Remove the two top bolts (See Fig 27) that secure
the auger housing to the motor mount frame.
e Place the weight transfer system in transport (re-
leased) postion
eThe auger housing and the motor mount frame will
separate, hinged by the bottom two bolts If the
auger housing and the motor mount do not sepa-
rate, slightly loosen the bottom two bolts._
e Remove the belt from the auger drive enginepulley
e Place the new belt on the large lower pulley (at-
tached to the back of the auger housing)..
eEngage the auger drive clutch lever. Place the
weight transfer system in the (engaged) lowest
position to pivot the auger housing and the motor
mount frame into the proper position.
eRelease the auger drive clutch lever' and reinstall
the bolts removed in the steps above_ Tighten the
lower bolts ifthey were loosened.
e Place the drive belt on the auger drive engine
pulley.
eAdjust the drive belt (see To Adjust Auger Drive
Belt paragraph on page 17).
e Adjust the belt guides (see To Adjust The Belt
Guides paragraph on page 19).
eReinstall the belt cover.
e Reconnect the spark plug wire.
.._,,:,...._ ...,,,.DRIVE PULLEY:
3t32 INCH"_'_K _ "_-- BELT GUIDE
BELT GUIDF_:._\ •"_(Left Hand)

,.o?. ,- ,.c,

I._l }_IMPELLER
JH,H ,,,,I llll I,,,
FIG. 26
iiiii
TRACTION
DRIVE.
BELT "_
AUGER DRIVE ...........
PULLEY
DRIVE
BELT
AUGER IDLE
PULLEY
BOLl"TOBE
REMOVED AUGER HOUSING
FIG, 27
"[RACK DRIVE BELT
If your' snow thrower witl not move forward, check the
track drive belt for wear. If the track drive belt needs tobe
replaced, proceed asfollows:
eDisconnect the spark plug wire.
®Remove the belt cover (See Fig,.23).
ePull the track drive idler' pulley (See Fig. 27) back
and slip the belt past the idler pulley..
eRemove the belt from the engine pulley. It may be
necessary to loosen and move the auger drive
engine pulley to allow the belt to beremoved.
oPlace the shift rod lever inthe 6th (all the wayto the
right) position. The belt can be removed between
the rubber drive disc and the drive disc plate.
eInstall the new original equipment replacement belt
in reverse order'of removal.
e
o
o
If the auger drive pulley was removed, reposition
the pulley and tighten the set screw. Be sure the
pulley on theengine is aligned with the large lower
pulley attached to the back side of the auger hous-
ing and the key onthe engine is flush with the end
of the shaft..
Reinstall the belt cover.
Reconnect the spark plug wire
18