OPERATION

-oWith mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the

ground_ Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and

tighten securely..

Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE

WHEEL

MOUNTING

BRACKET

SHOULDER

GAUGE WHEEL"

_//

BOLT

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch.. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine..

o Select desired height of cut.

oLower mower with attachment lift control..

Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

...._'

 

6AU'TION:_o

 

not operate the mowe_r

 

_

 

without either

the entire

grass catcher,

I

_

_

on

mowers

so. equipped, or thee dis-dis- I

 

 

charge guard

In place:

 

t

ATTACHMENT

CLUTCH

 

 

ATTACHMENT LIFT

 

SWITCH PULL-OUT TO_

 

 

'LEVER HIGH

 

 

 

 

 

 

 

POSITION

 

 

 

 

 

"_

Vh /

POSITION

 

ENGAGE__

 

 

 

 

 

 

HEIGHT /

f_'"-\_\_

ADJUSTMENT .._,_'_--_

KNOB ")_))_

FIG. 10

oIf stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

-Move motion control lever to neutral (N) position..

IMPORTANT: THE MOTION CONTROL LEVER DOES

NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.

,,To restart movement, slowly release parkingbrake and clutch/brake pedal°

. Slowly move motion control lever to slowest setting. o Make all turns slowly,

TO TRANSPORT (See Fig, '11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling

position° Free whee{ control is located at the rear drawbar of tractor,

Raise attachment lift to highest position with attach_ merit lift control,,

oPull freewheel control knob out and hold in position by inserting retainer spring into forward hole of control rod.

oDo not push or tow tractor at more than two (2) MPH, o To reengage transmission, reverse above procedure. NOTE: To protect hood from damage when transporting your tractor on atrucker a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc,)

FIG. 11

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 15)

oThe engine in your tractor has been shipped, from the factory, already filled with summer weight oil,

oCheck engine oil with tractor on level ground.

.

Remove

oil fill cap/dipstick

and wipe clean, reinsert the

 

dipstick

and

screw cap tight, wait for a few seconds,

 

remove

and

read oil level.

If necessary, add oil until

 

"FULL" mark on dipstick is reached.. Do not overfill.

oFor cold weather operation you should change oil for easier starting (See "OIL VISCOSITY CHART" in the Customer Responsibilities section of this manual).

oTo change engine oil, see the Customer Responsibili- ties section in this manual..

TO OPERATE ON HILLS

_:

Do

notdri_

 

 

_

hills with slopes

greater

than

15° and

!_

do not drive..across any

slope,

I

oChoose the slowest speed before starting up or down hiJls.

oAvoid stopping or changing speed on hills.

oIf slowing is necessary, move throttle control lever to slower position,

ADD GASOLINE

oFiN fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 1t7octane° (Use of leaded gasoline will increase carbon and lead oxide deposits

and reduce valve life), Do not mix oil with gaso{ine, Purchase fuel in quantities that can be used within 30

days to assure fuel freshness,

IMPORTANT; WHEN OPERATING tNTEMPERATURES

BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER

14 STARTING

Page 14
Image 14
Sears 917.25667 owner manual Before Starting the Engine, To Operate Mower See Fig, To Operate on Hills, ADD Gasoline