PRODUCT | SPECnFICATIONS |
|
|
|
| ||
MODEL | NUMBER | 917.387023 |
|
| |||
SERIAL | NUMBER |
|
|
|
| ||
DATE | OF | PURCHASE |
|
|
|
| |
HORSEPOWER: |
| &0 |
|
|
| ||
DISPLACEMENT: |
| 11o5 CUd IN. |
|
| |||
GASOLINE | CAPACITY/TYPE: | 1.5 QUARTS |
|
| |||
|
|
|
| UNLEADED | REGULAR | ||
OIL TYPE | SAE | 30 (ABOVE 32°F) | |||||
|
|
|
| SAE | 5W.30 | (BELOW | 32°F) |
OIL CAPACITY: |
| 20 OZS. |
|
| |||
SPARK | PLUG(GAP: .030") | CHAMPION | RJIgL |
| |||
VALVECLEARANCE: | INTAKE: | .004 - _008 | |||||
|
|
|
| EXHAUST _. | :004.. | ,008 | |
SOLID | STATE | IGNITION |
|
|
|
| |
AIR GAP: |
|
| ,0125 | IN. |
|
| |
BLADE | BOLT TORQUE: | FT. LBS, |
| ||||
"The model and serial numbers will be found on a decal attached to the rear of the
lawn mower housing,Record both serial number and date of purchase in space provided above
LAWN | MOWER |
|
|
|
| ° Remove blade and attaching hardware | ||||||||||||||||
Always | observe safety rules when performing |
| (bolt, |
| lock washer | and hardened | washer). | |||||||||||||||
any maintenance. |
|
|
|
| NOTE: |
| Remove | the blade | adapter | and check | ||||||||||||
TIRES |
|
|
|
|
|
|
| the key |
| inside | hub of blade | adapter. The key | ||||||||||
• | Keep | tires free of | gasoline, | oil, | or insect | must be | in good | condition to work | properly. | |||||||||||||
| control chemicals | which can | harm rubber. | Replace | adapter | if damaged. |
|
|
| |||||||||||||
o | Avoid | stumps, stones, deep | ruts, sharp | TO REPLACE | BLADE |
|
|
|
|
| ||||||||||||
| objects and other hazards that may cause | o | Position | the | blade | adapter | on the engine | |||||||||||||||
| tire damage |
|
|
|
| |||||||||||||||||
|
|
|
|
|
| crankshaft. | Be sure | key | in adapter and | |||||||||||||
BLADE | CARE |
|
|
|
|
| ||||||||||||||||
|
|
|
|
| crankshaft | keyway | are aligned, |
|
| |||||||||||||
For best results, mower blade must be kept |
|
|
| |||||||||||||||||||
,, | Position | blade | on the blade | adapter aligning | ||||||||||||||||||
sharp. Replace bent qr damaged blades. | ||||||||||||||||||||||
| the two (2) holes in the blade with the raised | |||||||||||||||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||||
TO REMOVE | BLADE |
|
|
|
| lugs on the adapter. |
|
|
|
|
| |||||||||||
o | Disconnect | spa_rkplug wire | from spark plug | ,, | Be sure the trailing edge of blade (opposite | |||||||||||||||||
| and place | wire where it cannot | come in |
| sharp | edge) | is up | toward | the engine, |
| ||||||||||||
| contact | with spark | plug. |
|
|
| o | install the blade bolt with | the rock washer | |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
o | Turn | lawn | mower | on its side. Make sure air |
| and | hardened | washer into blade | adapter | |||||||||||||
| filter and carburetor are up. |
|
|
|
| and | crankshaft. |
|
|
|
|
|
|
| ||||||||
|
|
|
| ° | Use block of wood | between | blade and lawn | |||||||||||||||
,, | Use a wood block between | blade and | ||||||||||||||||||||
| mower | housing to prevent | blade from |
| mower | housing | and | tighten | the blade | bolt, | ||||||||||||
| turning | when removing blade | bolt, |
| turning | clockwise, |
|
|
|
|
|
| ||||||||||
,, | Protect | your hands with gloves | and/or wrap | • | The | recommended |
| tightening torque | is 35- | |||||||||||||
| blade | with | heavy | cloth. |
|
|
|
| 40 f1,,Ibs. |
|
|
|
|
|
|
|
| |||||
| Remove | blade bolt by turning | counter- | IMPORTANT: | Blade | bolt is grade | 8 heat | |||||||||||||||
| clockwise. Use a 9/I 6" box or | treated_ |
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
wrench.
