ENFORCER CCD IR DAY/NIGHT CAMERA MANUAL

ENFORCER CCD IR DAY/NIGHT CAMERA MANUAL

Specifications

EV-1323C12DWQ (NTSC)

EV-1323B12DWQ (EIA)

 

EV-132C-DW2Q (NTSC)

 

EV-1353C12DWQ (PAL)

EV-1353B12DWQ (CCIR)

 

EV-135C-DW2Q (PAL)

 

Type

Color camera

B/W camera

 

 

 

Chip

1/3” CCD, Sony

1/3” CCD, A1 PROs

 

 

 

Resolution

420 TV lines

Pickup elements

512 x 492 pixels (NTSC / EIA)

A.

Camera

F.

BNC connector (female)

B.

Adjustable Sunshield

G.

Adjustment nut

C.

Mounting bracket

H.

Mounting holes

D.36” cord

E.DC jack

Parts List

1 x IR camera

3 x Mounting screws

1 x Sunshield

3 x Screw anchors

1 x Mounting bracket

1 x Manual

1 x Pigtail connector

 

 

512 x 582 pixels (PAL / CCIR)

Scanning system

2:1 interlace

 

 

Sync

Internal

 

 

Video output

1V pp composite output, 75 ohms

 

 

Lens

EV-1323C12DWQ / EV-1323B12DWQ (4 3mm)

 

EV-1353C12DWQ / EV-1353B12DWQ (4.3mm)

NOTE: For additional pigtail connectors, inquire SECO-LARM’s EVA-F5521-3Q pigtail connector with 3-ft. length cable.

Use SECO-LARM’s included Pigtail Connector for easy installation and serviceability.

Important:B

Do not remove label or open case as warranty will be voided.

 

EV-132C-DW2Q / EV-135C-DW2Q (2 9mm)

Viewing Angle*

EV-1323C12DWQ / EV-1323B12DWQ (78o)

 

EV-1353C12DWQ / EV-1353B12DWQ (78o)

 

EV-132C-DW2Q / EV-135C-DW2Q (120o)

Minimum illumination

 

0.1 lux (LED off), 0.0 lux (LED on)

Gamma correction

 

0.45

 

 

 

 

S/N ratio

>50dB (AGC off)

 

>48dB (AGC off)

 

 

 

 

Shutter control

 

Auto Electronic Shutter (AES)

 

1/60~1/100,000 sec. (NTSC / EIA), 1/50~1/100,000 sec. (PAL / CCIR)

 

 

 

E

 

 

 

 

 

® nrared t

 

 

 

D

 

 

 

 

Day/Nig

 

 

 

 

 

 

 

ENFORCER

 

 

 

 

 

 

 

Important:

 

 

 

F

 

 

 

 

 

 

 

G A

 

 

 

 

 

 

 

 

 

Do not cut DC Jack (E) or

 

 

 

C

 

 

 

 

 

 

Video Jack (F) as warranty

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

will be voided.

 

 

 

 

 

 

 

Hx3

 

 

 

 

 

 

 

Backlight compensation

 

 

auto

 

 

 

 

 

Automatic gain control (AGC)

 

 

auto

 

 

 

 

Enclosure

 

IP68 weatherproof

 

 

 

 

 

# of infrared LEDs

 

 

12

 

 

 

 

Max. LED range

 

Up to 40 ft. (12m)

 

 

 

 

Power source

 

12VDC±10%

 

 

 

 

Power consumption

100mA (IR off), 230mA (IR on)

 

110mA (IR off), 240mA (IR on)

 

 

 

 

Operating temperature

 

14°~131° F (-10°~55° C)

Dimensions

1

1

 

 

BEFORE STARTING

1.Please read this manual carefully and keep it for future reference.

2.Use the camera within given temperature and electricity limits.

3.Do not aim the LED light directly at the eyes when the LEDs are on.

4.Do not point the camera at the sun. Heat could damage the camera, even when not in use.

5.Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.*

6.Do not open or disassemble the camera. There are no user- serviceable parts inside.

7.Do not drop the camera or subject it to strong vibrations.

*Note: Many video monitors produce strong electromagnetic fields close to the display CRT, especially when the monitor is turned on or during de-Gaussing, which occurs automatically with many monitors when the monitor is turned on.

 

3 /16”(L) x 2 /4”(D) (78 x 57 mm) (without sunshield)

 

 

Weight

16 oz. (454g)

 

 

 

* All viewing angles are approximate

INSTALLATION

1. Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be

7. Mount the bracket to the wall using the three included mounting

screws. If the wall is made of dry wall, brick, or similar material, it

Dimensions:

21/4” (57mm)

211/16” (68mm)

29/16” (65mm)

ENFORCER® InfraredDay/Night

31/16” (78mm)

9/16” (14.5mm) 113/16” (46mm)

mounted (if necessary).

2.Assemble the mounting bracket; then screw it into the back of the camera. Make sure the mounting base is tightened to the bracket.

3.Temporarily connect the camera to the 12VDC power supply.

Do not cut DC jack or video jack as warranty will be voided. Use the included SECO-LARM’s pigtail connector.

4.Temporarily connect the camera’s female BNC connector to the video cable’s male BNC connector.

5.While watching the monitor, hold the camera bracket against the wall by hand where it is to be mounted, then twist the camera until it is certain that this mounting location is correct. Use a pencil to mark the location of the three screw holes in the bracket.

6.Disconnect the 12VDC power supply and video cable.

may be necessary to use the three included screw anchors.

8. Reconnect the 12VDC power supply and video cable. Turn the monitor

on, and make sure the camera is sending the proper video signal.

9. Adjust the camera angle:

(a) Loosen and tighten the bracket’s thumb screw to turn the

camera and change its angle relative to the bracket. This

ensures the camera is pointing in the right direction.

(b) Loosen and tighten the adjustment plate to rotate the camera

on its axis. This rotates the angle of the video image.

10. Tighten the bracket’s thumb screw and the adjustment plate so

that the camera does not move, but not so tight that it cracks the

case or bracket.

11. Do a final test of the video camera and monitor.

Page 1 Page 2
Page 2
Image 2
SECO-LARM USA EV-1323C12DWQ, EV-1353C12DWQ, EV-1353B12DWQ, EV-132C-DW2Q, EV-1323B12DWQ Specifications, Parts List
Page 1 Page 2

1353B12DWQ, EV-135C-DW2Q, EV-1323C12DWQ, EV-1353B12DWQ, EV-135C-DW2Q (2 9mm) EV-1323C12DWQ specifications

SECO-LARM USA presents an innovative line of access control solutions with the EV-132C-DW2Q, EV-132C-DWL8Q, EV-132C-DWLDQ, EV-132C-DWL6Q, and EV-1323C12DWQ models. These devices are designed to enhance security while providing versatility and ease of use for various applications.

The EV-132C-DW2Q is a robust door strike designed specifically for access control systems. It operates smoothly with a high tensile strength, enabling it to withstand a considerable amount of force. With a fail-safe design, this strike ensures that the door unlocks during a power failure, providing a safe exit for occupants.

The EV-132C-DWL8Q takes advantage of dual-voltage capabilities, operating at both 12V and 24V DC, making it suitable for different systems. This adaptability allows for seamless integration into existing setups, offering flexibility without sacrificing security.

Meanwhile, the EV-132C-DWLDQ includes an electromagnetic locking feature that enhances user experience. This model is particularly beneficial in environments requiring an additional layer of security, combining traditional locking methods with advanced technology.

For applications needing more compact solutions, the EV-132C-DWL6Q offers a smaller profile without compromising functionality. It features a simplified installation process, making it an ideal choice for new installations or upgrades.

The EV-1323C12DWQ model is specifically designed for heavy-duty use, featuring a durable housing that can withstand extreme weather conditions and tampering. This unit is excellent for outdoor applications, ensuring reliable access control in various environments.

Common technologies across this series include fail-secure and fail-safe operations, ensuring that these devices can meet different security needs. They are crafted from high-quality materials to endure both environmental and physical challenges while ensuring longevity.

These models also feature adjustable voltage capabilities and come with various mounting options, simplifying integration into pre-existing security frameworks. Additionally, they all provide a GUARDIAN certification, denoting high-quality engineering and compliance with international standards.

In summary, SECO-LARM USA's EV-132C series offers a comprehensive range of access control solutions suited for diverse applications. With a focus on reliability, user convenience, and advanced technology, these models stand out in the field of security enhancement.
Top Page Image Contents