SECO-LARM USA SK-1011-SQ Digital Access Keypad Manual, Page, SECO-LARMU.S.A., Inc, Outputs

Digital Access Keypad Manual

INSTALLER PROGRAMMING

These functions should only be used by professional installers, as incorrect entries can disable the entire keypad function.

Enter Programming Mode							(DEFAULT: 0 0 0 0 )
Enter Master code				Confirm			Function
X X X X *				*			Enter into programming mode
*Key in the Master Code.
Note: For first-time use, Master code is						0 0	0 0
Data Refresh
Option			Confirm	Function
8	9 0	1	#	Clears all previously stored data.
Configure Relay Outputs							(DEFAULT: Momentary, 1-sec. output)
Option		Output time		Confirm		Function
4	0	1 to 999		#		Relay momentary mode, from 1 to 999 seconds
4	1			#		Relay shunt mode (ON/OFF)
Relay Output Inhibit Control (lockout mode)							(DEFAULT: Momentary, 1-sec. output)
Option		Code Entry		Confirm		Function
5	0	1 to 999		#		Lockout for 1 to 999 seconds
5	1			#		Lockout shunt mode (ON/OFF)
Wrong Code Lockout							(DEFAULT: 10 tries / 30 seconds)
Option			# of tries	Confirm	Function
7	0				After 10 successive wrong codes, 30-second lockout
7	1				After 10 successive wrong codes, Duress activated
7	2		5 to 10	#	After 5 to 10 wrong codes, 15-min. lockout - Can reset with Master Code
7	6 0	0		#	None of the above
Output Activation Announcer							(DEFAULT: On)
Option		Code entry		Confirm	Function
		{	1	#	1-sec. beep notifies the user to open the door when the output relay is activated with the
8	1				user code or egress button. Use with a locking device which gives no sound when it
					activates, such as a magnetic lock.
			0	#	The beep is disabled, replaced by 2 short beeps for valid user codes.
User Code Entry Mode							(DEFAULT: Manual)
Option		Code entry		Confirm	Function
		{	1	#	Auto Entry Mode is selected. The # key that follows the user code is NOT required in
8	2				code entry. The User Codes MUST be set to the same digit length as the Master Code,
					from 4-8 digits.
			0	#	Manual Entry Mode is selected. The # key that follows the user code is required in
					code entry. The User Codes can be 4-8 digits, but not necessarily all of the same length.
Keypress Beeps							(DEFAULT: On)
Option		Code entry		Confirm	Function
8	3	{	1	#	Keypad beeps when a key is pressed.
			0		Silent operation -- keypad does not beep when a key is pressed.
				#

Exit Programming Mode

Confirm Function

*Exits programming mode, returns keypad to normal operations

USER CODE WORKSHEET

To print out a blank worksheet where all user codes can be recorded, please visit www.seco-larm.com and select the Model #, "SK-1011-SQ" in the drop down menu for the burglar section. On the product page click on "User Code Worksheet," which will load the .PDF.

Digital Access Keypad Manual

SPECIFICATIONS:

Power:

•Operation voltage -- 12-24 Volts AC/DC. No jumper needed to set voltage.

•Stand-by current drain -- 10mA @12VDC.

•Active current drain (press keypad key) -- Under 30mA.

•Active current drain (relay activated) -- Under 80mA.

Outputs:

•Relay output -- 5A @ 28VDC, Form "C", N.O./C./N.C., programmable for 1 to 999 second timed output or shunt (start/stop) output. Three terminals.

•Tamper output -- N.C. output. Connect to tamper circuit of alarm control panel. Two terminals.

Inputs:

•Power -- 12-24Volts AC/DC. Two terminals.

•Egress -- N.O., ground (-). Single terminal.

Code Operation:

•Up to 100 user codes, 10,000 possible user code combinations.

•Max. 10 seconds to enter each digit.

•Max. 30 seconds to enter each code.

Dimensions (keypad with back box):

•4-5/8" x 2-7/8" x 1-7/8" (117 x 74 x 48 mm).

Weight (keypad with back box):

•6.3 oz. (180 grams).

WIRING (SAMPLE INSTALLATION):

	Tamper	(+) (--)	OUTPUT 1					EG
	N.C.	12~24V AC/DC	N.C.			C. N.O.
Connect to the N.C.				(+)
24hr. zone of alarm
panel or other
signalling device.				N.C.			N.O.
					OR

+	--		Electric
12VDC		+	Lock	--
	power
	supply

	(for DC		REMARKS:
Diode			Output relay
	use only)		N.O. output for fail-secure lock.
1N4004			N.C. output for fail-safe lock.
Cathode				Additional egress buttons
Egress button (inside the
		N.O.	N.O.	can be connected in parallel
protected premises)				as needed

Page 6 SECO-LARM U.S.A., Inc. Page 3