TOUCHKEY IMMOBILIZER

SLI® 762FP-ISS

VALET MODE and EMERGENCY DISARM

1.VALET MODE – The Immobilizer automatically arms 30 seconds after the engine is turned OFF. However there may be certain times (for repair or if the Touchkeys are lost, for instance) that arming the Immobilizer is not desired. Note: When in the valet/override mode, the LED flashes while the ignition is turned OFF to help deter thieves. When the ignition is turned ON, the LED will turn OFF.

2.EMERGENCY DISARM – If the Touchkey is lost, the engine will not start, even with the proper car keys. In this case, the Immobilizer must be put into the valet/override mode using the emergency disarm procedure.

3.EMERGENCY DISARM/VALET MODE

Note: Immobilizer must be armed before you can enter your PIN.

a.Know the secret PIN. For the following example, assume the PIN is 503. Note: Count 10 flashes for the number “0”.

b.While the LED is flashing (because the Immobilizer is armed), turn the ignition ON. The LED will show steady ON.

c.Turn the ignition OFF and the LED will start flashing. Count the flashes. After the 5th flash, turn the ignition ON. The LED will show steady ON again. (This is your PIN’s first digit—5.)

d.Turn the ignition OFF and count the flashes. After the 10th flash, turn the ignition ON. The LED will show steady ON again. (2nd digit, 0)

e.Turn the ignition OFF and count the flashes. After the 3rd flash, turn the ignition ON. The LED will show steady ON again. (3rd digit, 3)

f.At this point, the LED will show steady ON for 10 seconds then OFF to indicate the Immobilizer is in the valet/override mode.

4.EXITING THE VALET/OVERRIDE MODE – Insert a valid Touchkey into the receptacle. EXIT VALET/OVERRIDE MODE AS SOON

AS POSSIBLE TO PREVENT THEFT OF YOUR VEHICLE.

POWER DOWN AND POWER UP

1.If power is ever removed from the Immobilizer and then restored, it will return to the state prior to removing power (If armed when power was removed, it returns armed. If disarmed when power is removed, it remains disarmed.)

2.While driving (when the ignition switch is ON), if the main power is cut to the Immobilizer, the car will continue to function normally.

CODE LEARNING NEW TOUCHKEYS

1.NUMBER OF TOUCHKEYS – The Immobilizer comes factory coded to the two Touchkeys included in the package. The unit can learn the codes of up to 4 Touchkeys.

Note – This procedure deletes the existing Touchkey Codes. Therefore, you must do this procedure for both existing and new Touchkeys at the same time.

2.CODE LEARNING PROCEDURE

Note: Immobilizer must be armed before you can enter your PIN.

a.Add the digits ―55‖ to the end of your secret 3-digit PIN. (For example, if the PIN is 503, the 5-digit code learning PIN

is 50355).

b.While the LED is flashing (indicating the Immobilizer is armed), turn the ignition ON. The LED will turn steady ON.

c.Turn the ignition OFF and count the flashes. After the 5th flash, turn the ignition ON. The LED will be steady ON again.

(This is your PIN’s first digit—5.)

d.Turn the ignition OFF and count the flashes. After the 10th flash, turn the ignition ON. The LED will be steady ON again.

Note: “0”=10 flashes (2nd digit, 0)

e.Turn the ignition OFF and count the flashes. After the 3rd flash, turn the ignition ON. The LED will flash rapidly. (3rd digit, 3)

f.Turn the ignition OFF and count the flashes. After the 5th flash, turn the ignition ON. The LED will be OFF. (4th digit, 5)

g.Turn the ignition OFF and count the flashes. After the 5th flash, turn the ignition ON. The LED will flash rapidly. (5th digit, 5)

h.Leave the ignition key ON. Once the LED stops flashing, insert a Touchkey into the receptacle within 10 seconds. The LED will turn steady ON to show the Touchkey was successfully learned. (Repeat for all touch keys.)

3.EXIT THE CODE LEARNING PROCEDURE – There are three ways to do this:

a.Turn the ignition switch OFF.

b.Wait more than 10 seconds to insert a new Touchkey.

c.If memory is full (you try to learn a 5th Touchkey), the unit will

go into valet/override mode.

Note: If new codes are programmed, all of the existing Touchkeys must also be re-programmed.

4.MISTAKES – If the PIN is incorrectly keyed in, simply start over from the first digit. Ignore any digits that have already been keyed in.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship.

The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

Copyright © 2009 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

 

 

 

 

 

 

SECO-LARM ®

Tel: 1-800-662-0800

(Domestic U.S. & Canada)

Email: info@seco-larm.com

Website: www.seco-larm.com

 

16842 Millikan Avenue, Irvine CA 92606

Tel: 1-949-261-2999

(California and International)

Fax: 1-949-261-7326

PITTW3 mi-SLI 762FP-ISS OWNERS.docx

Page 1 Page 2
Page 2
Image 2
SECO-LARM USA SLI 762FP-ISS owner manual Power Down and Power UP, Code Learning NEW Touchkeys, Emergency DISARM/VALET Mode
Page 1 Page 2

SLI 762FP-ISS specifications

SECO-LARM USA has set a standard for security solutions with its SLI 762FP-ISS model, designed to enhance security and streamline access control for various applications. This state-of-the-art infrared sensor is not just a robust security measure, but also a versatile tool that blends seamlessly into modern security setups.

One of the standout features of the SLI 762FP-ISS is its advanced infrared technology. This sensor boasts a range of up to 32 feet, making it effective for monitoring both indoor and outdoor environments. Its passive infrared (PIR) detection capability allows it to sense motion based on heat emitted by objects, which is particularly useful in security applications where swift reactions to movement are crucial.

The SLI 762FP-ISS is equipped with a dual-zone detection pattern, which enhances its sensitivity and minimizes false alarms. This ensures that only significant movement is detected, significantly improving the overall efficiency of the security system. Furthermore, its adjustable sensitivity settings allow users to customize detection parameters based on specific needs and environmental conditions.

One of the marked characteristics of this sensor is its ability to integrate smoothly with existing security systems. Its relays can be easily interfaced with alarms, access controls, or surveillance systems, providing flexibility in how it can be employed. The device supports both NO (Normally Open) and NC (Normally Closed) relay configurations to accommodate various installation requirements.

In terms of durability, the SLI 762FP-ISS is built to withstand different weather conditions, making it suitable for outdoor use. Its resilient housing protects against moisture and dust, ensuring reliability and longevity in various environments.

Another notable characteristic is its ease of installation. The sensor comes with comprehensive mounting hardware and a clear installation guide, enabling users to set it up quickly and efficiently without extensive technical expertise.

In conclusion, the SECO-LARM USA SLI 762FP-ISS infrared sensor is a powerful and adaptable tool for enhancing security measures. With its advanced detection technology, customizable features, and rugged design, it stands out as a reliable option for businesses and homeowners looking to bolster their security infrastructure. Whether used in a residential setting or a commercial environment, the SLI 762FP-ISS delivers superior performance that security professionals and everyday users can depend on.
Top Page Image Contents