Shark NV100 manual Using the Vacuum Emptying the Dust Cup Assembly

Using the Vacuum

Emptying the Dust Cup Assembly

English

For suction to reach the power nozzle, the extension wand and stretch hose must be attached securely on the vacuum body.

DO NOT pull vacuum cleaner around by the hose.

DO NOT over-extend the hose. Always hold the vacuum so that it does not tip over.

The height of your power nozzle has been optimized for easy pushing and superior cleaning on all foor types. There is no need to make any height adjustments as you transition to different foor & carpet types.

For best results empty the Dust Cup Assembly after each use; or as needed during prolonged usage. or when it reaches the MAX fll line.

DO NOT OVERFILL.

Turn vacuum off before emptying.

Dust cup

Release

Button

Fig. 16

Fig. 7

Fig. 11

Fig. 9

Fig. 10

Indicator Light

Fig. 8

Fig. 12

Fig. 13

Fig. 14

Fig. 15

TO EMPTY THE DUST CUP

Your Shark® Navigator™ can be used to clean all surface types.

1Plug in the vacuum.

2Push the Power button (). (Fig. 7)

3Place your foot on the power nozzle and pull the handle back towards you. (Fig. 8)

NOTE: This vacuum has a separate brushroll button

()on the top of the vacuum. (Fig. 9)

4CLEAN CARPETS:

Engage the brushroll by pushing the brushroll button () to the “ON” position. The brushroll light will turn green. (Fig. 9)

IMPORTANT: To protect your carpets, the brushroll will only turn on when you have pulled the handle back towards you and released the power nozzle.

IMPORTANT: The brushroll indicator light on the power nozzle will illuminate solid red if there is a blockage.

(Fig. 10) This feature is designed to protect your Lifetime Belt that powers your brushroll. See

Checking for Blockages on page 11.

5CLEAN BARE FLOORS:

For cleaning bare foors or to clean with the hose, push the brushroll button () to the “OFF” position for suction only. The brushroll light will turn off. The brushroll will not spin in this mode.

6CLEAN ABOVE-FLOORS WITH HOSE:

You can attach the accessories onto the handle or onto the extension wand for a longer reach.

aStand the vacuum into upright position.

bTo remove the handle only, press the handle release button.

(Fig. 11)

cTo remove the handle with the extension wand, press the extension wand release button on the back of the vacuum. (Fig. 12)

dPush the selected tool into the end of the handle or handle with extension wand for longer reach and begin cleaning.

To order additional parts and accessories, go to www.sharkclean.com.

ASSEMBLY:

1Press the Dust Cup release button and remove the dust cup from the vacuum. (Fig. 13)

2Grip carry handle and press the bottom Dust Cup Door release button. (Fig. 14)

3Option A: for Quick Empty: Insert Dust Cup Assembly deep inside trash receptacle to contain dust and debris. (Fig. 15)

Press the bottom Dust Cup Door release button; tap container gently to dislodge and release dust and debris.

Close the bottom door until it snaps in place.

Important: If the Dust Cup Door does not swing open freely after pressing the release button, push the door open using the bottom door tabs.

4Option B: For Allergy Sufferers: Wrap a trash bag around the Dust Cup Assembly leaving space at the bottom for the door to swing open. (Fig. 16)

Locate the Dust Cup Door release button within the trash bag and press to release as you shake the dust cup to empty dust and debris.

Close the bottom door until it snaps in place.

Note: Option B can also be performed outside of the home to further minimize releasing dust back into the air. Carry just the Dust Cup Assembly and trash bag outside.

Fig. 18

Fig. 17

Note: It may become necessary to occasionally clean the metal screen inside the dust cup. To clean, press the top dust cup release button (Fig. 17), pull out the metal screen and remove any excess dirt. Then replace the metal screeen inside the dust cup and close the top lid.

(Fig. 18)

6 TOLL FREE: 1-800-798-7398

NV100_26_IB_ENG_110317_2.indd 6-7

www.sharkclean.com 7

11-03-17 10:40 AM