Sharp AR-153E, AR-157E 1, 2

32

MISFEED REMOVAL

When the misfeed ( ) indicator blinks or blinks in the display, the unit will

stop because of a misfeed. If a misfeed occurs when using the RSPF/SPF, a number

may appear in the display after a minus sign. This indicates the number of the

originals that must be returned to the original feeder tray after a misfeed. Return the

required number of originals. Then this number will disappear when copying is

resumed or the clear ( ) key is pressed. When the RSPF/SPF misfeeds an

original sheet, the unit will stop and the RSPF/SPF misfeed ( ) indicator will blink,

while the misfeed ( ) indicator will remain off. For a misfeed of originals in the

RSPF/SPF, see "E: Misfeed in the RSPF/SPF" (p.35).

1Open the multi-bypass tray, and side cover, in that order.

To open the multi-bypass tray, see "BYPASS FEED (including special

paper)" (p.10). To open the side cover, see "TONER CARTRIDGE

REPLACEMENT" (p.25).

2Check the misfeed location. Remove the misfed paper

following the instructions for each location in the illustration

below. If the misfeed ( ) indicator blinks, proceed to "A:

Misfeed in the paper feed area" (p.33).

If the unit is turned on with the lower side cover open, the misfeed ( )

indicator will blink. In this case, close the lower side cover. The misfeed

( ) indicator will go out.

If paper is misfed here, proceed to "A:

Misfeed in the paper feed area". (p.33)

If paper is misfed here, proceed

to "D: Misfeed in the lower

paper feed area". (p.35)

If paper is misfed here, proceed to "B:

Misfeed in the fusing area". (p.33)

If the misfed paper is seen from

this side, proceed to "C: Misfeed

in the transport area". (p.34)

Contents

Main AR-153E AR-157E Return to Directory Page 1 CAUTIONS Caution label on the unit Cautions on using Warning: Cautions on handling Proper storage for supplies Trademark acknowledgements Safety precautions: CONTENTS 1INTRODUCTION 2LOADING PAPER 8 6 1 4 USING THE MANUAL Conventions used in the manual AR-153E 5 PART NAMES 6 OPERATION PANEL 2 7 PAPER 8 LOADING THE PAPER TRAY 1 2 3 4 10 BYPASS FEED (including special paper) Print face face down) all the way into the multi-bypass tray. 1 2 3 Note for loading envelopes 3 12 COPY FLOW 13 POWER ON About the scan head Initial settings of operation panel 14 1 2 Setting a large original (AR-153E) 1 2 Using the RSPF/SPF 1 2 Original face up of originals. 3 original feeder tray. Stream feeding mode 1 2 Automatic exposure adjustment 1 2 3 4 5 1 2 select the desired copy ratio. 3 Page 4 1 2 A B C 3 1 1 2 23 3 4 USER PROGRAMS 2 3 4 24 5 6 DISPLAYING TOTAL NUMBER OF COPIES 1 2 5 25 TONER CARTRIDGE REPLACEMENT 1 2 3 4 5 6 28 CLEANING THE UNIT Page 6 30 This chapter describes misfeed removal and troubleshooting. TROUBLESHOOTING If any problem occurs, check the list below before contacting the SHARP service center. 31 STATUS INDICATORS 32 MISFEED REMOVAL 1 2 A: Misfeed in the paper feed area 1 2 B: Misfeed in the fusing area 1 2 3 C: Misfeed in the transport area 1 2 3 4 D: Misfeed in the lower paper feed area 1 2 3 E: Misfeed in the RSPF/SPF (AR-157E) Roller rotating knob Reversing tray Page 7 38 SYSTEM CONFIGURATION PRINTER/SCANNER EXPANSION KIT (AR-PG2) SINGLE PASS FEEDER (AR-SP5) 2 3 4 5 8 40 CD-ROM SOFTWARE FOR THE SHARP PERSONAL MFP SERIES MFP driver 41 HARDWARE AND SOFTWARE REQUIREMENTS BEFORE INSTALLATION Flow of installation 43 INSTALLING THE SOFTWARE Installing onto Windows XP (USB/parallel interface) 2 4 5 installed on the screen, and then click the "Start" button. 6 was selected in step 4). 1 7 8 9 10 11 12 Installing onto Windows 98/Me/2000 (USB interface) 2 4 5 6 7 8 1 2 3 4 2 4 5 6 7 setup (This step will start if it was selected in step 4). 6 1 2 8 selected in step 4). 1 2 3 53 INDICATORS ON THE OPERATION PANEL SCANNER indicator ONLINE indicator Start indicator 2 3 4 How to print 1 2 3 4 media type, and print quality, and then click the "Print" button to start printing. About interrupt copying 56 USING THE SCANNER MODE 1 2 3 4 1 2 3 4 5 Scan Button Destination Setting Dialog Box Flow of the Button Manager setting Page 1 2 3 4 Opening the scanner driver and scanning from your computer 1 2 Page 1 2 3 4 5 1 2 3 4 Page 66 USING OTHER INSTALLED DRIVERS 2 3 4 5 6 1 2 3 Page 9 69 SPECIFICATIONS Page Optional equipment Printer/Scanner Expansion Kit (AR-PG2) 250-sheet paper feed unit (AR-D16) Single pass feeder (AR-SP5) 72 INDEX 2 A B M N O P R Z INDEX BY PURPOSE SOFTWARE LICENSE 2. Restrictions. 3. Termination. 4. Export Law Assurances. 5. Government End Users. 6. Limited Warranty on Media. 7. Disclaimer of Warranty on Software. 8. Limitation of Liability. 9. Controlling Law and Severability. 10. Complete Agreement. { Section 1. Product Identification Section 2. Suppliers Name and Address Section 3. Ingredients Section 4. Hazardous Identification (Emergency Overview) Section 6. Physical Chemical Characteristics Section 7. Fire and Explosion Data Section 8. Reactivity Data Section 9. Precautions for Safe Handling and Use Section 10. Regulatory Information MATERIAL SAFETY DATA SHEET Section 1. Product Identification Section 2. Suppliers Name and Address Section 3. Ingredients Section 4. Hazardous Identification (Emergency Overview) Section 6. Physical Chemical Characteristics Section 7. Fire and Explosion Data Section 8. Reactivity Data Section 9. Precautions for Safe Handling and Use Section 10. Regulatory Information NOTICE