SPECIFICATIONS
PRODUCT TYPE

DVD Video Player

DISCS PLAYBACK COMPATIBILITY

DVD-Video / DVD-RW/-R / DVD+RW/+R / Audio CD / CD-RW/-R

FREQUENCY RESPONSE

DVD (linear sound) : 20 Hz to 22 kHz (sample rate: 48 kHz) 20 Hz to 44 kHz (sample rate: 96 kHz)

CD :20 Hz to 20 kHz

SIGNALTONOISE RATIO S/N RATIO

CD :

120 dB (JEITA)

DYNAMIC RANGE

 

 

DVD (linear sound) :

102 dB

 

CD :

99 dB (JEITA)

TOTAL DISTORTION FACTOR

 

DVD :

1 KHz

0.0045% (JEITA)

CD :

1 KHz

0.0035% (JEITA)

WOW AND FLUTTER

 

 

Below the measurement limitation (+/-0.001% W PEAK) (JEITA)

• Designs and specifications are subject to change without notice.

CONNECTIONS

Video output

One RCA connector, 1 Vpp (75 Ω)

Component video output

One pin jack (Y), 1 Vpp (75 Ω)

 

Two pin jacks (CR/PR, CB/PB),

 

700 mVpp (75 Ω)

S-video output

Mini DIN 4-pin jack (75 Ω)

Analog audio output

Two RCA connectors

 

(one left channel, one right channel)

 

2 Vrms (47 kΩ)

Coaxial digital audio output

One pin jack, 500 mVpp (75 Ω)

POWER SOURCE

 

120 V ~ +/- 10%, 60 Hz +/- 0.5%

POWER CONSUMPTION

10 W (standby: 0.8 W)

OPERATING TEMPERATURE

41 F° to 104 F° (5 °C to 40 °C)

DIMENSIONS

W:2.5 inch (62 mm) H: 9.8 inch (248.5 mm) D: 9.4 inch (238 mm)

WEIGHT

Approx 2.9 lbs. (1.3 kg)

 

 

TROUBLESHOOTING GUIDE

 

If this unit does not perform properly when operated as instructed in this Operation Manual, check this unit consulting the following checklist.

 

PROBLEMCORRECTIVE ACTION

 

No power.

• Make sure the power plug is connected to an AC outlet.

 

 

• Make sure the power is turned on.

 

The unit turns off suddenly.

• Check if the “AUTO POWER OFF” is set to “OFF”.

 

This unit does not respond to the remote

• Check if the power plug is connected to an AC outlet.

 

control.

• Check the batteries in the remote control.

 

 

• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles

 

 

between the sensor and the remote.

 

 

• You have to be within 23 feet (7 m) of this unit.

 

No picture.

• Connect the video cable firmly.

 

 

• Insert a correct video disc that plays on this unit.

 

Disc cannot be played.

• Insert the disc.

 

 

• Clean the disc.

 

 

• Insert the disc correctly with the label facing to the left when the unit is installed vertically.

 

 

• Insert the disc correctly with the label facing up when the unit is installed horizontally.

 

 

• Cancel the parental lock or change the control levels.

 

 

• Handle a disc with special care so that it does not have fingerprints, scratches, or dusts on its surface.

 

 

• If the recorded portion of the disc is too small (less than 2 3/16 inches (55 mm)), it may not play

 

 

back properly.

 

No sound.

• Connect the audio cable firmly.

 

 

• Turn the power of the audio component on.

I

 

• Correct the audio output settings.

NFORMATION

 

• During the playback of a 2-layered disc, pictures may stop for a moment. This happens while the

 

 

• Correct the input settings on the audio component.

 

No DTS audio is output.

• Use a DIGITAL AUDIO OUT jack when outputting the DTS audio.

 

Distorted picture.

• Connect this unit directly to the TV.

 

 

• There are some cases where picture may be slightly distorted, and those are not a sign of a malfunction.

 

 

1st layer is being switched to the 2nd layer. This is not a malfunction.

 

 

• Check if the INTERLACE/PROGRESSIVE mode is set correctly according to your TV. See page 8.

 

 

• This happens right after fast forwarding or rewinding. This is not a malfunction.

 

Audio or subtitle language does not

• The selected language is not available for audio or subtitles on the DVD.

 

match the set up.

This is not a malfunction.

 

The camera angle cannot be changed.

• The DVD does not contain sequences recorded from different camera angles.

 

 

This is not a malfunction.

 

Audio or subtitle language cannot be

• The DVD does not contain audio source or subtitles in the selected language.

 

changed.

This is not a malfunction.

 

“Prohibited icon” appears on the screen,

• That operation is prohibited by this unit or the disc. This is not a malfunction.

 

prohibiting an operation.

 

 

• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Operation Manual for details on correct operations.

 

• Playback from a desired track and random playback are not available during programmed playback.

 

• Some functions are prohibited on some discs.

 

SERVICE INFORMATION (FOR THE U.S.)

 

For the location of the nearest SHARP Authorized Service Center, or to obtain product literature, accessories, supplies or customer assistance,

 

please call 1-800-BE-SHARP(1-800-237-4277) or visit SHARP’s website (http://www.sharpusa.com).

– 20 –

EN