Sharp GX-M10H(OR), GX-M10H(RD) operation manual Maintenance

Troubleshooting chart (continued)

■ USB

Symptom	Possible cause
● Device cannot be	● There is no MP3/WMA file
detected.	inside the device.
	● The device is not properly
	connected.
	● A MTP device is connected.
	● The device contains AAC
	file only.
● Playback does not	● A copyright-protected WMA
start.	or false MP3 file is being
	played back.
● Wrong time display.	● A Variable Bitrate files are
● Wrong file name	being played back.
display.	● The File Name was written
	in other than English
	characters.

■iPod, iPhone or iPad

Symptom	Possible cause
● No sound is	● The iPod, iPhone or iPad is
produced.	not playing.
No image appears	● The iPod, iPhone or iPad is
on the TV/monitor.	not properly connected to
	the unit.
	● The AC power lead of the
	unit is not plugged in.
	● The video cable is not
	properly connected.
	● The TV/monitor’s input
	selection is not properly set.
	● The iPod TV out feature has
	not been set to output video.
	● USB/iPad terminal do not
	support video.
● iPod, iPhone or	● The iPod, iPhone or iPad is
iPad will not	not making full contact with
charge.	the connector.
	● Using iPod (3rd generation).
	● The iPod or iPhone is not
	supported. Refer to page 7
	for compatible models.
● “This accessory is	● The iPhone battery is low.
not made to work	Please charge the iPhone.
with iPhone” or	● iPhone is not properly
“This accessory is	docked.
not supported by
iPhone” appears on
iPhone screen.

■Condensation

Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet (CD pickup, etc.) or on the transmitter on the remote control. Condensation can cause the unit to malfunction. If this happens, leave the power on with no disc in the unit until normal playback is possible (about 1 hour). Wipe off any condensation on the transmitter with a soft cloth before operating the unit.

If such a problem occurs, do the following:

1Set the unit to the stand-by mode and turn the power on again.

2If the unit is not restored in the previous operation, unplug and plug in the unit again, and then turn the power on.

Note:

If neither operation above restores the unit, clear all the memory by resetting it.

■Factory reset, clearing all memory

1Press the ON/STAND-BY button to enter the power stand-by mode.

2Whilst pressing down the VOLUME + button, press the ON/STAND-BY button until “RESET” appears.

Caution:

This operation will erase all data stored in memory including clock, timer settings and tuner preset.

■Care of compact discs

Compact discs are fairly resistant to damage, however mistracking can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your CD collection and player.

●Do not write on either side of the disc, particularly the non-label side from which signals are read. Do not mark this surface.

●Keep your discs away from direct sunlight, heat, and excessive moisture.

●Always hold the CDs by the edges. Fingerprints, dirt, or water on the CDs can cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the centre, along the radius.

NO	YES
	Correct

Maintenance

■Cleaning the cabinet

Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then with a dry cloth.

Caution:

●Do not use chemicals for cleaning (petrol, paint thinner, etc.). It may damage the cabinet.

●Do not apply oil to the inside of the unit. It may cause malfunctions.

■If problem occurs

When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction.

E-21

12/10/26 12_GX-M10H_OM_EN.fm