Sharp PGD210U Computer Mode Memory Adjustments

E-20

Computer Mode Memory Adjustments

• The projector has been preset with different modes for

use with XGA and other compatible computers.

However, 7 memory positions are provided to store

mode adjustments.

• Each memory position can be used to store mode

adjustments to match the computer.

1. Press the ENTER button to select the

Memory Adjustment mode

• Press the MENU button. While the MENU screen

is displayed, press the ADJUSTMENT ƒ/∂ but-

tons to select “RGB1 INPUT ADJ.” Press the

ENTER button. The MENU mode changes as

shown.

• While the RGB INPUT adjustment menu is dis-

played, press the ADJUSTMENT ƒ/∂ buttons to

select “MEMORY SELECT”. Then press the

ENTER button to change the image.

2. Press the ADJUSTMENT ß/© buttons

• The screen shown on the left will appear. There

are 7 memory positions.

• Press the ADJUSTMENT ƒ button once to move

to the following screen. Press the ADJUSTMENT

ß/© buttons to select the number of the memory

you want to adjust. If that memory position has

not been set, the screen on the right will be dis-

played. If it has been set, the screen on the left

will be displayed. MEMORY No. 0 cannot be set.

It contains the fixed factory preset settings.

• To make or change a setting, press the ADJUST-

MENT ƒ/∂ buttons to move the cursor to “SET-

TING.” Then press the ENTER button to go to the

RGB INPUT adjustment menu screen. (If you do

not want to make any adjustments, press the

MENU button.)

• Select the item you want to adjust by pressing the

ADJUSTMENT ƒ/∂ buttons, then use the AD-

JUSTMENT ß/© buttons to make the adjust-

ments. When adjustments are completed, press

the MENU button. The display disappears and

the adjustments are stored in memory as a user

mode. See page 19 for details on the adjustment

items.

3. Press the MENU button anytime to exit

RGB INPUT ADJ.

1 When RGB 1 or 2 is selected.

2

RGB1 ADJ.

RGB1 INPUT ADJ.

IMAGE ADJ.

AUDIO

SYSTEM SETUP

LANGUAGE

:SEL. :NEXT

ENTER

:END

MENU

RGB1 INPUT ADJ.

PHASE

H-POS

V-POS

MODE

RESET

MEMORY SELECT

+

0

0

0

0

:SEL. :NEXT

ENTER

:END

MENU

[

OFF

]

-

+

-

+

-

+

-

CLOCK

MEMORY SELECT

:SEL.

:ADJ.

ENTER

:END

MENU

0 1 2 3 4 5 6 7

STANDARD SETTING STANDARD SETTING

SETTING

:ENTER

MEMORY SELECT

SETTING

:SEL. :BACK

ENTER

:END

MENU

0 1 2 3 4 5 6 7

MEMORY SELECT

NON

SETTING

:SEL.

:ADJ.

ENTER

:END

MENU

0 1 2 3 4 5 6 7

:ENTER

MEMORY SELECT

:SEL.

:ADJ.

ENTER

:END

MENU

0 1 2 3 4 5 6 7

RESOLUTION

HOR FREQ

VERT FREQ

SETTING

:ENTER

HzKHz 60.0

75

1024×768

On-Screen Display

Contents

Main PG-D210U LCD PROJECTOR PROJECTEUR LCD PROYECTOR LCD OPERATION MANUAL MODE DEMPLOI MANUAL DE OPERACION Indice ES ENGLISH E FRANAIS F ESPAOL Dear SHARP Customer Important Information Model No.: PG-D210U Serial No.: Important Safeguards Cautions Concerning the Laser Pointer CAUTION Notes on Operation About the Temperature Monitor Function: Outstanding Features Location of Controls FRONT VIEW SIDE AND REAR VIEW OPERATION PANEL ON TOP OF PROJECTOR Operating the Wireless Mouse Remote Control Wireless Mouse Remote Control FRONT VIEW Using the remote control in a dark room Remote control handling precautions CAUTION Wireless Mouse Functions Connection Example remote control can help you create a more professional presentation. Functions and Operations CAUTION Setting Up the Projector Using the Focus and Zoom E-10 Height of Projector Adjust to match the setup configuration. Projector Distance and Picture Size Relationship Distance from screen Picture size: 100 inches (254 cm) Using the Image Invert/Reverse Function 22. Reversed Image Mode 33. Inverted Image Mode 44. Reversed Inverted Image Mode 5. Press the MENU button anytime to exit IMAGE ADJ. Example of a ceiling-mount setup Example of a standard setup Using the horizontal reverse function makes the following setups possible. Example of a reversed image setup AUDIENCE SIDE Adjusting the Height of the Picture 1. Press the adjuster release and lift the projector to the desired angle with both hands Use the carrying handle when carrying the projector. 2. Remove your hand from the adjuster release 3. Make any minor adjustments necessary Connecting the Projector (RGB 1, 2: Computer) Rear terminals Personal computer COMPUTER CONTROL CABLE Plug and Play Function Connecting to the Computer RGB Input (RGB 1, 2)/Output Terminals 2 624 or 1,024 480, 832 640 5. Connecting an external monitor 5 3. Connecting to other compatible computers 4. Connecting to the COMPUTER AUDIO INPUT 4 Input Signals (Recommended Timing) V-SYNC C-SYNC(V) wxyz For IBM and compatibles For Apple Macintosh Series RGB Adjustment Controls RGB Input Adjustments (CLOCK, PHASE, V-POS and H-POS) 3. Press the MENU button anytime to exit RGB INPUT ADJ. Description of Adjustment Items Computer Mode Memory Adjustments 1. Press the ENTER button to select the Memory Adjustment mode 2. Press the ADJUSTMENT / buttons 3. Press the MENU button anytime to exit RGB INPUT ADJ. 1 Basic Operation of the Projector 1 1. Connect the AC cord Connect the supplied AC cord to the AC inlet on the back of the projector. 1 2 2. Turn on the MAIN POWER 6. Select input 7. Press INPUT CHECK 8. Adjust the volume 9. To turn off the power from the projector or the remote control 6 Adjusting the Picture Adjusting the Picture 1. Use the MENU button to select the mode to be adjusted 2. Adjust the Picture Description of Adjustment Items Adjusting the Audio Adjusting the Audio Description of Adjustment Items Functions on the Projector Setting Up the System Checking the system and lamp usage time Selecting the Remote Mouse Background Level Using the Black Screen Function Black Screen On-Screen Display Override Using the Blue Screen Function Using the Input Mode On-Screen Display Override Function REMAIN 5M REMAIN 4M REMAIN 1M Air Filter Maintenance Bottom Air Filter 4 6 1 3 Clean the AIR FILTER. 5Replace the AIR FILTER. Replace the FILTER COVER. Turn OFF the MAIN POWER. 2Remove the AIR FILTER. Lamp/Maintenance Indicators Lamp Maintenance Indicators Before Calling for Service Lamp Replacement How to Change the Lamp Removing the lamp unit (see figure) Installing the lamp unit Resetting the lamp timer Connection Pin Assignments Analog RGB 1 and 2 Signal Input and Analog RGB Output T erminal: RS-232C terminal: D-sub female connector Mouse Input T erminal (for IBM/Mac): RS-232C Terminal Specifications 1. PC control 4. Commands 2. Communication conditions 3. Basic format R RABR 1 0__ 1OK R E-36 Wired Remote Control Terminal Specifications T 0001 1. Specifications of wired remote control input 3.5 minijack External: `5 V (1 A) Internal: GND Specifications Video signal Specifications are subject to change without notice. Wave length Max. output Dimensions