Manuals / Brands / Computer Equipment / Projector / Sharp / Computer Equipment / Projector

Sharp PGD210U Using the Blue Screen Function, Using the Input Mode On-Screen Display Override Function

1 40

Download 40 pages, 497.84 Kb

E-28

Using the Blue Screen Function

This projector is equipped with a Blue Screen function

that will turn the screen blue when the video input termi-

nal is not connected to anything, or the video component

is turned off.

• Press the MENU button. While the MENU screen is displayed,

press the ADJUSTMENT ƒ/∂ buttons to select “IMAGE

ADJ.”. Then press the ENTER button to display the “IMAGE

ADJ.” screen as shown. Press the ADJUSTMENT ƒ/∂ but-

tons to select “BLUE SCREEN,” and press the ADJUST-

MENT ß/© buttons to select “ON” or “OFF”. Press the MENU

button to return to the normal screen.

• When the Blue Screen function is on, the screen will turn blue

when no video signal is being input through the video input

terminal.

• When the Blue Screen function is on, and no video signal is

input via the input terminal for more than 15 minutes, the

power is automatically turned off.

• The indicators appear as shown each minute before the

power is turned off, from 5 minutes before until 1 minute

before.

Notes:

• The Blue Screen function does not operate in RGB mode.

• When the power is turned off, the POWER indicator will light red.

• To turn the power on again, press the POWER button to set it to OFF,

then press it again to set it to ON.

On-Screen Display

Using the Input Mode On-Screen DisplayOverride Function

The On-Screen Displays that appear during input select

(“RGB 1,024 2 768, 75 Hz,” etc.) can be turned off.

Once “INPUT DISPLAY” is turned off, the On-Screen Dis-

plays will not appear even if the INPUT CHECK button on

the remote control is pressed.

• Press the MENU button. While the MENU screen is displayed,

press the ADJUSTMENT ƒ/∂ buttons to select “IMAGE

ADJ.”. Then press the ENTER button to display the “IMAGE

ADJ.” screen as shown. Press the ADJUSTMENT ƒ/∂ but-

tons to select “INPUT DISPLAY,” and press ADJUST-

MENT ß/© buttons to select “ON” or “OFF”.

• When OFF is selected, the On-Screen Display (“RGB

1,024 2 768, 75 Hz,” etc.) will not be displayed during input

select.

BLUE SCREEN

BLK SCRN DISP

IMAGE ADJ.

REVERSE

INVERT

INPUT DISPLAY

[

OFF

]

[

OFF

]

[

OFF

]

SYSTEM

[

OFF

]

[

ON

]

:SEL.

:ADJ. :END

MENU

REMAIN 5M

REMAIN 4M

REMAIN 1M

BLK SCRN DISP

IMAGE ADJ.

REVERSE

INVERT

INPUT DISPLAY

:SEL.

:ADJ. :END

MENU

[

OFF

]

[

OFF

]

[

OFF

]

[

OFF

]

Contents

Main PG-D210U LCD PROJECTOR PROJECTEUR LCD PROYECTOR LCD OPERATION MANUAL MODE DEMPLOI MANUAL DE OPERACION Indice ES ENGLISH E FRANAIS F ESPAOL Dear SHARP Customer Important Information Model No.: PG-D210U Serial No.: Important Safeguards Cautions Concerning the Laser Pointer CAUTION Notes on Operation About the Temperature Monitor Function: Outstanding Features Location of Controls FRONT VIEW SIDE AND REAR VIEW OPERATION PANEL ON TOP OF PROJECTOR Operating the Wireless Mouse Remote Control Wireless Mouse Remote Control FRONT VIEW Using the remote control in a dark room Remote control handling precautions CAUTION Wireless Mouse Functions Connection Example remote control can help you create a more professional presentation. Functions and Operations CAUTION Setting Up the Projector Using the Focus and Zoom E-10 Height of Projector Adjust to match the setup configuration. Projector Distance and Picture Size Relationship Distance from screen Picture size: 100 inches (254 cm) Using the Image Invert/Reverse Function 22. Reversed Image Mode 33. Inverted Image Mode 44. Reversed Inverted Image Mode 5. Press the MENU button anytime to exit IMAGE ADJ. Example of a ceiling-mount setup Example of a standard setup Using the horizontal reverse function makes the following setups possible. Example of a reversed image setup AUDIENCE SIDE Adjusting the Height of the Picture 1. Press the adjuster release and lift the projector to the desired angle with both hands Use the carrying handle when carrying the projector. 2. Remove your hand from the adjuster release 3. Make any minor adjustments necessary Connecting the Projector (RGB 1, 2: Computer) Rear terminals Personal computer COMPUTER CONTROL CABLE Plug and Play Function Connecting to the Computer RGB Input (RGB 1, 2)/Output Terminals 2 624 or 1,024 480, 832 640 5. Connecting an external monitor 5 3. Connecting to other compatible computers 4. Connecting to the COMPUTER AUDIO INPUT 4 Input Signals (Recommended Timing) V-SYNC C-SYNC(V) wxyz For IBM and compatibles For Apple Macintosh Series RGB Adjustment Controls RGB Input Adjustments (CLOCK, PHASE, V-POS and H-POS) 3. Press the MENU button anytime to exit RGB INPUT ADJ. Description of Adjustment Items Computer Mode Memory Adjustments 1. Press the ENTER button to select the Memory Adjustment mode 2. Press the ADJUSTMENT / buttons 3. Press the MENU button anytime to exit RGB INPUT ADJ. 1 Basic Operation of the Projector 1 1. Connect the AC cord Connect the supplied AC cord to the AC inlet on the back of the projector. 1 2 2. Turn on the MAIN POWER 6. Select input 7. Press INPUT CHECK 8. Adjust the volume 9. To turn off the power from the projector or the remote control 6 Adjusting the Picture Adjusting the Picture 1. Use the MENU button to select the mode to be adjusted 2. Adjust the Picture Description of Adjustment Items Adjusting the Audio Adjusting the Audio Description of Adjustment Items Functions on the Projector Setting Up the System Checking the system and lamp usage time Selecting the Remote Mouse Background Level Using the Black Screen Function Black Screen On-Screen Display Override Using the Blue Screen Function Using the Input Mode On-Screen Display Override Function REMAIN 5M REMAIN 4M REMAIN 1M Air Filter Maintenance Bottom Air Filter 4 6 1 3 Clean the AIR FILTER. 5Replace the AIR FILTER. Replace the FILTER COVER. Turn OFF the MAIN POWER. 2Remove the AIR FILTER. Lamp/Maintenance Indicators Lamp Maintenance Indicators Before Calling for Service Lamp Replacement How to Change the Lamp Removing the lamp unit (see figure) Installing the lamp unit Resetting the lamp timer Connection Pin Assignments Analog RGB 1 and 2 Signal Input and Analog RGB Output T erminal: RS-232C terminal: D-sub female connector Mouse Input T erminal (for IBM/Mac): RS-232C Terminal Specifications 1. PC control 4. Commands 2. Communication conditions 3. Basic format R RABR 1 0__ 1OK R E-36 Wired Remote Control Terminal Specifications T 0001 1. Specifications of wired remote control input 3.5 minijack External: `5 V (1 A) Internal: GND Specifications Video signal Specifications are subject to change without notice. Wave length Max. output Dimensions