Sharp PN-ZS701 operation manual Specifications, To ensure safe and correct use

Models: PN-ZS701

1 2
Download 2 pages 23.22 Kb
Page 1
Image 1
Specifications

TIPS

Back

The supplied clamps can be attached to the stand rods and shelf board

 

 

 

 

bar to hold the cables.

Clamp position

 

 

 

 

Clamp

 

 

 

 

 

 

 

 

Specifications

Operation Manual TROLLEY STAND PN-ZS701

Applicable models (as of September 2011) LCD MONITOR PN-L702B

Model

PN-ZS701

Height

4 positions

adjustment

Center height of the screen

 

Approx. 1310 mm (51-9/16 inch) [A],

 

approx. 1210 mm (47-5/8 inch) [B],

 

approx. 1110 mm (43-11/16 inch) [C],

 

approx. 1010 mm (39-3/4 inch) [D]

 

(Depends on the position of the mounting

 

brackets attached in Step 1-(4).)

Dimensions

See the diagram at right

Weight

Approx. 48 kg (105.8 lbs.)

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units.

There may be some deviations from these values in individual units.

Units: mm (inch) (Note that the values shown are approximate values.)

899 (35-3/8)

1500 (59-1/16)

(Available models differ according to region.)

Thank you for purchasing a SHARP product.

Before using the product, please be sure to read this operation manual carefully. In particular, be sure to read the section “To ensure safe and correct use”. After reading the manual, keep it in a convenient location where it can be accessed at any time.

TIPS

-This product was shipped after strict quality control and inspection; however, if breakage or a malfunction should be found, contact your SHARP dealer or your nearest customer contact.

-Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.

-This product and its accessories may be upgraded without advance notice.

To ensure safe and correct use

This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays and labels and incorrectly using the product could have results as classified below.

Please read the following warning symbol information before reading the rest of this section, and be sure to strictly observe all instructions.

Warning: Not following these instructions could result

Caution: Not following these instructions could result

1980 (77-15/16)

Printed in China

TINSE1212MPZZ(1)

in death or serious injury.

The installation must be performed by qualified service personnel.

Improper installation work may cause the monitor to fall or topple over, resulting in injury.

Do not place the stand on an unstable surface. Do not subject to intense shock or vibration.

Toppling or falling may occur, causing injury.

Only use this product with specified models. Do not modify the stand or the accessories.

Otherwise, the monitor may fall or the stand may topple over, resulting in injury.

Lock the casters when using the stand.

Toppling may occur, causing injury.

Do not transport the stand with a monitor attached.

If the monitor mounting attachments become broken or damaged, the monitor may fall or the stand may break or topple, resulting in injury.

Use the supplied screws. Tighten all screws firmly. Insufficient tightening may cause the monitor to fall or the stand to topple over, resulting in injury.

in injury or property damage.

Do not climb onto or lean on the stand and monitor.

Toppling may occur, causing injury.

If deformation or cracks are discovered, stop using the stand.

Using the stand without repairing the problem may cause the monitor to fall or the stand to topple, resulting in injury.

Take suitable preventative measures to reduce the risk of this product falling or toppling due to an earthquake or other circumstances.

The equipment for preventing falling and toppling will not be effective if the wall or table to which the equipment is attached is not sufficiently strong. Reinforce the wall or table sufficiently. These measures to prevent falling and toppling are intended to reduce the risk of injury and other harm, however, their effectiveness is not guaranteed in all earthquakes.

– 4 –

– 1 –

Page 1
Image 1
Sharp operation manual Specifications, To ensure safe and correct use, Operation Manual TROLLEY STAND PN-ZS701