Sharp R990J(S), R-980J operation manual Installation Instructions, Oven Diagram

4) High rack

5) Cook book

6) Operation manual

A42430, SCA/SCNZ R980J/990J(S) O/M

INSTALLATION INSTRUCTIONS

1.Remove all packing materials from the oven cavity, (do not remove the waveguide cover), and the feature sticker from the outside of the door, if there is one. Check the unit for any damage, such as a misaligned door, damaged gaskets around the door or dents inside the oven cavity or on the door. If there is any damage, please do not operate the oven until it has been checked by a SERVICE CENTRE APPROVED BY SHARP and repaired, if necessary.

2.Accessories provided

1) Turntable tray

2) Roller stay

3) Low rack

3.Since the door may become hot during cooking, you should place or mount the oven so that the bottom of the oven is 80 cm or more above floor. You should also keep children away from the door to prevent them burning themselves.

4.Locate the roller stay in the centre of the oven, then fit the turntable on the roller stay. Make sure the turntable and roller stay are centrally located and locked together. NEVER operate the oven without the roller stay and turntable.

5.The oven should not be installed in any area where excessive heat and steam are generated, for example, next to a conventional oven unit. When the oven is mounted on a kitchen benchtop, allow at least 40 cm on the top, 5 cm on both sides and at the rear of the oven for adequate air circulation. The ventilation openings should not be blocked. WARNING: The electrical outlet must be readily accessible so that the unit can be unplugged easily in an emergency.

6.Neither the manufacturer nor the distributors can accept any liability for damage to the machine or personal

injury for failure to observe the correct electrical connecting procedure. The A.C. voltage must be single phase • 230V-240V, 50Hz

7.This appliance must be earthed.

8.Operate the oven from a general purpose domestic outlet.

If a generator is used, do not operate the oven with non-sinusoidal outputs.

9.Building the oven into the wall. A Sharp built-in kit model number RK-J90W for R-980J and RK-J90S for R- 990J(S) are available which enable the microwave oven to be integrated within a kitchen, the kit is available from your retailer. This built-in kit has been tested according to Australian Standards. Sharp does not recommend the use of any other built-in kit. If the oven is to be positioned near a conventional oven, ensure that adequate space is allowed, and a suitable heat shield is incorporated between the two to prevent damage to the oven and the built-in kit caused by heat.

10.Before using CONVECTION HEATER ELEMENTS for the first time, operate the oven without food for 20 minutes at 250°C. This will allow the oil that is used for rust protection to be burned off.

OVEN DIAGRAM

(R-980J)

6	15	10			12
					9
3		11			8
					TOP
					7
4	5		2	4	13
(R-990J(S))
6	15	10			12
					9
3	11				8
					TOP
					7
4	5		2	4	13

116

17

18

14

116

17

18

14

1.Ventilation openings

2.Oven lamp

3.Door hinges

4.Door safety latches

5.See through door

6.Door seals and sealing surfaces

7.Door open button

8.Touch control panel

9.Digital readout

10.Waveguide cover (Do not remove)

11.Coupling

12.Menu label

13.Rating label

14.Power supply cord

15.Oven cavity

16.Outer cabinet

17.Turntable

18.Roller stay

Metal racks——High and low

The racks are for Convection, Mix and Grilling. When cooking on Convection or Mix, do not substitute similar

types of racks for these specially designed ones.

High Rack

-This rack is used for two level cooking in Convection, such as layer cakes, muffins, biscuits, etc., or for Grill cooking.

Low Rack

-This rack is recommended for roasting and baking in Convec- tion or Mix mode and can be used for reheating and cooking foods by microwave.

WARNING:

The accessories will become very hot when in use. Use thick oven gloves when inserting/removing the food or turntable from the oven to PREVENT BURNS.

5

SCA/SCNZ R980J 1-13 5 04.8.4, 10:48 AM