Sharp XV-Z2000 -55

Appendix

-55

Maintenance indicator Problem Cause Possible solution

Temperature

warning

indicator

Normal Abnormal

Off Red on

(Standby)

The internal

temperature is

abnormally high.

Abnormal

• Blocked air intake

•Relocate the projector to an area

with proper ventilation (see page

7).

•Cooling fan break-

down

•Internal circuit failure

•Clogged air intake

•Takethe projector to your nearest

Authorized SharpVision Service

Center or Dealer for repair.

•Clean the exhaust and intake

vents. (See page 53.)

Lamp

indicator

Red on

(Standby) The lamp does

not illuminate. •Burnt-out lamp

•Lamp circuit failure

•Carefully replace the lamp. (See

page57.)

•Takethe projector to your nearest

Authorized SharpVision Service

Center or Dealer for repair.

•Please exercise care when

replacing the lamp.

Red on Time to change

the lamp. •Remaining lamp life

becomes 5% or less.

Green on

Green blinks

when the lamp

is warming up

or shutting

down.

Info

•If the temperature warning indicator illuminates and the projector enters the standby mode, check whetherany of the ventilation holes are blocked (page 7) and then try turning the power back on. Wait until theprojector has cooled down completely before plugging in the power cord and turning the power back on.(At least 10 minutes.)•If the power is turned off for a brief moment due to power outage or some other cause while using theprojector, and the power supply recovers immediately after that, the lamp indicator will illuminate in redand the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the powercord in the AC outlet and then turn the power on again.•Do not unplug the power cord after the projector has entered the standby mode and while the cooling fanis running. The cooling fan runs for about 90 seconds.

The lamp does

not illuminate. —

•Disconnect the power cord from

the AC outlet, and then connect it

again.

Contents

Main XV-Z2000 ENGLISH -1 WARNING: See bottom of projector. Introduction CAUTION IMPORTANT Model No.: XV-Z2000 Serial No.: WARNING: PRODUCT DISPOSAL Declaration of Conformity WARNING: Contents Preparing Setup Connections Introduction Quick Start Accessories Supplied accessories Note Optional accessories Marks Used in This Operation Manual IMPORTANT SAFEGUARDS CAUTION Ensure that you read the following safeguards when setting up your projector. IMPORTANT SAFEGUARDS Caution regarding usage of the projector Other connected equipment Using the projector in other countries Temperature monitor function Part Names and Functions Front View Numbers in refer to the main pages in this operation manual where the topic is explained. Top View About the Indicators on the Projector Part Names and Functions Projector (Rear View) Remote Control Part Names and Functions Using the Remote Control Inserting the Batteries 1 and remove the cover towards the direction of the arrow. 2 1. Pages 21-28 3. This section shows the basic operation. For details, see the page described below for each step. Setup and Projection 4. Pages 32, 33 2 1 Pages 30, 31 Setting Up the Projector Setup -17 Side View There may be an error of 3% in the above values. Screen Size and Projection Distance Setting Up the Projector Projecting a Reversed Image Projection from behind the Screen Projection Using a Mirror Ceiling-mount Setup Connections -19 INPUT Terminals and Connectable Main Equipment -20 Samples of Cables for Connection Connecting to Video Equipment -22 When connecting the video equipment with RGB output terminal (INPUT 5) Before connecting the cable, switch the digital input type switch to VIDEO. DVD Player,etc. Connecting to Video Equipment When connecting the component video equipment to the DVI input terminal on the projector (INPUT 5) Before connecting the cable, switch the digital input type switch to VIDEO. Page Connecting to Video Equipment -24 When connecting video equipment with S-video output terminal (INPUT 3) When connecting video equipment with video output terminal (INPUT 4) DVD Player,etc. Connecting to a Computer Connecting to a computer (INPUT 5) Connecting to a computer with DIGITAL RGB output Terminal (DIGITAL) Plug and Play function Connecting to a Computer Controlling the Projector by a Computer When connecting to a computer using an RS-232C serial control cable Turning the Projector On/Off Connecting the Power Cord 2 Turning the Power Off Plug the supplied power cord into the AC socket. Image Projection Basic Operation Switching the INPUT Mode Press , , , , or on the remote control to select the input Adjusting the Focus 1 2 trol to adjust the focus. Adjusting the Projected Image Size 1 2 trol to adjust the zoom. Using the Adjustment Feet 1 2 3 Horizontal Keystone Correction Vertical Keystone Correction 1 to enter the Keystone Correction 2 or V Keystone. 3 1 3 4 2 5 Selecting the Picture Mode Switching the High Bright- ness / High Contrast Mode Adjusting the Picture Aspect Ratio Basic Operation -36 Menu Items *2: Item when inputting RGB signal through INPUT 5 Auto Sync [ON/OFF] Special Modes Signal Info Options menu Main Menu Page 52 Language menu Main Menu Sub Menu Using the Menu Screen Menu icons 2 ENTER button MENU button UNDO button Adjustment buttons ('/"/\/|) 3 To adjust the projected image while viewing it 4 5 -40 1 The Picture menu screen for the selected input mode is displayed. 2 || |or \\ \\ \to display the other menu screens. 3 4 5 6 You can adjust the projectors picture to your preferences using the Picture menu. Picture Adjustment (Picture menu) Adjusting the Image 2 Description of Adjustment Items Adjusting the Color Temperature 1 ture menu on the menu screen and 2 '' 'or "" "" "to fine adjust the gamma correction. Picture Mode Function Picture Adjustment (Picture menu) Switching the High Bright- ness/High Contrast Mode Description of IRIS Settings Computer Image Adjustment (Fine Sync menu) Adjusting the Computer Image Description of Adjustment Items Special Modes Setting INPUT 5 (Component) mode Auto Sync Adjustment Computer Image Adjustment (Fine Sync menu) Description of Auto Sync Adjustment Checking the Input Signal You can use the Options menu to enhance the usage for the projector. Using the Options Menu Setting On-screen Display Description of OSD Display Settings Setting the Video System Using the Options Menu INPUT 4 mode Description of Video Systems Signal Type Setting Eco Mode Description of Eco Mode Selecting a Background Image Description of Background Images -50 Auto Power Off Function Using the Options Menu Menu operation Page 40 Description of Auto Power Off Selecting the Menu Screen Position Selecting the Menu Color Selecting the On-screen Display Language 1 Example: Language menu screen for 3 2 guage menu icon ( ). Maintenance Maintenance Indicators Maintenance Indicators About the temperature warning indicator About the lamp indicator -55 Lamp Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP Caution Concerning the Lamp Replacing the Lamp Regarding the Lamp 1 on the remote control to put the projector into standby mode. AC socket 2 3 4 5 6 Resetting the Lamp Timer 1 Connecting Pin Assignments RS-232C Port: 9-pin D-sub male connector DVI-I (INPUT 5) port : 29 pin connector DVI Digital INPUT DVI Analog RGB Input RS-232C Specifications and Command Settings C1 C2 C3 C4 P1 P2 P3 P4 Command 4-digit Parameter 4-digit O K Return code (0DH)E R R Return code (0DH) A @ Computer Compatibility Chart Computer DTV 15.7 31.5 15.6 31.3 45.0 28.1 Troubleshooting For SHARP Assistance (U.S.A. only) -63 Specifications -64 Dimensions Bottom View Units: inches (mm) Side View Side View Top View Rear View Glossary Index -67 CONSUMER LIMITED WARRANTY TOOBTAIN PRODUCT INFORMATION, CALL 1-877-DTV-SHARPOR VISIT www.sharpusa.com. VALID IN USA ONLY