Select the desired preset number (1~30)

Repeat the above steps 1 to 3 to memorize

3 and press the MEMORY button.

4 other stations.

 

T/P

 

 

 

TUNE

TUNE

 

MEMO

 

 

+

 

 

MEMORY

 

 

 

 

or

TREBLE

+

MUTE

 

 

BASS

 

 

 

 

+

 

 

 

VOL.

 

 

 

TUNE

MEMO

TUNE

 

 

 

 

+

 

 

FM MODE

VOL.

P.SCAN

 

• When using the NUMERIC buttons on the remote

MEMORY BACKUP FUNCTION

control.

 

 

 

The following items, set before the receiver is turned

Examples) For “3” :

3

 

 

off, are memorized.

For “15” :

within 2 seconds

 

• INPUT SELECTOR settings

1

 

5

• Preset stations,etc.

For “30” :

 

 

 

0

 

 

Note

• The station has now been stored in the memory.

• If the electricity fails or the AC input cord is

• When using the NUMERIC buttons, the station is stored

disconnected for more than 2 weeks, they are all

automatically without pressing the MEMO button.

cleared. So you should memorize them again.

A stored frequency is erased from the memory by storing another frequency in its place.

If “MEMO” goes off, start again from the above step 2.

Tuning to preset stations

 

 

 

 

 

Select the desired preset number.

 

 

 

 

 

2

 

 

 

 

 

 

After selecting the tuner as an input

 

 

 

 

 

DECK SEL.

TAPE

 

 

 

 

 

 

TREBLE +

BASS

 

 

 

 

 

 

 

 

 

 

 

B

 

1

source, select the preset mode.

 

 

 

 

 

 

 

 

+

 

 

 

 

 

 

TUNING/PRESET or

 

T/P

MUTE

 

 

 

 

 

 

TUNE

TUNE

VOL.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+TUNE

MEMO TUNE

 

 

A

 

 

 

 

 

 

 

 

 

+

 

DECK SEL.

TAPE

 

 

 

 

 

 

 

FM MODE

P.SCAN

 

 

B

 

 

 

 

 

 

 

 

 

VOL.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TREBLE

+

BASS

 

 

 

 

 

 

 

 

T/P MODE

T/P

 

 

+

 

 

 

 

 

 

 

 

T/P

 

MUTE

 

 

• When using the NUMERIC buttons on the remote

 

VOL.

 

 

 

or

 

MEMO

+

 

 

control.

 

 

 

 

 

 

 

TUNE

 

TUNE

 

 

Examples) For “3”

:

 

 

 

 

 

FM MODE

VOL.

P.SCAN

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For “15”

:

1

within 2 seconds

5

 

 

 

 

 

 

 

 

• Then “PRESET” lights up.

 

 

 

 

 

For “30”

:

0

 

 

 

 

 

 

 

• When selecting the desired preset number with the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NUMERIC buttons, the desired preset station will be

 

 

 

 

 

 

 

tuned to automatically without selecting the preset mode.

Listening to FM stereo broadcasts

 

 

Scanning preset stations in sequence

• While listening to FM broadcasts,

 

 

 

T/P

 

 

 

 

 

 

 

 

 

 

 

 

 

VOL.

T/P

 

MUTE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FM MODE

TUNE

MEMO

 

VOL.

 

 

 

 

 

 

 

 

 

FM MODE

VOL.

 

 

 

 

 

 

 

 

 

 

 

 

TUNE

 

TUNE

 

 

 

 

 

 

 

 

 

 

 

MEMO

+

 

P.SCAN

 

 

 

 

 

 

 

 

 

 

• Each time this button is pressed,

 

 

 

 

 

FM MODE

 

P.SCAN

 

 

 

 

 

 

 

VOL.

 

 

 

 

the FM mode changes as follows:

 

 

 

 

 

 

 

 

 

 

Stereo mode : “ST” lights up.

 

 

 

 

 

 

 

 

 

 

Mono mode : “ST” goes off.

 

 

 

 

 

 

 

 

 

 

 

• When FM stereo broadcasts are poor because of weak

• The receiver will start scanning the stations in the preset

broadcast signals, select the FM mono mode to reduce

sequence.

 

 

 

 

 

the noise, then FM broadcasts are reproduced in

 

 

• At the desired station, press this button again to stop

monaural sound.

 

 

 

 

 

scanning.

 

 

 

 

 

1 3

Page 13
Image 13
Sherwood RX-770 manual Tuning to preset stations, Memory Backup Function