Shindaiwa 80898, SP150 specifications Typical Nozzle Assemblies, Description Part Number Qty

Safety Precautions

Calibrating the Sprayer

Illustrated Parts List (SP150)

AIR

WATER

EARTH

Carefully read the labels on chemical contain- ers prior to use. Chemicals are classified in four categories of toxicity:

■Category I, High Toxicity, Red label

■Category II, Moderate Toxicity, Yellow label

■Category III, Low Toxicity, Blue label

■Category IV, Light Toxicity, Green label

There are unique handling recommendations for each category, and you should familiarize yourself with them.

Always wear clothing and safety equipment that will provide appropriate protection against the materials you are handling. Equipment may include, but not be limited to:

■Long sleeve shirt

■Impermeable apron or coverall

■Impermeable gloves and boots

■Wide-brim hat

■Protective mask equipped with appropriate filters

Do not eat, drink, or smoke while handling chemicals or while you are spraying. Always handle chemicals in a well ventilated area while wearing appropriate protective clothing and safety equipment. DO NOT STORE OR TRANS-

PORT CHEMICALS WITH FOOD OR MEDI- CINES, AND NEVER REUSE A CHEMICAL CONTAINER FOR ANY OTHER PURPOSE.

Keep chemicals out of the reach of children, animals, or other unauthorized people. When not in use, store chemicals in a safe place. Never blow through nozzles, valve, pipes or any other component by mouth!

When handling chemicals and when spraying, make sure you are operating in accordance with local, state, and federal environmental protection rules and guidelines. Do not spray in very hot or windy conditions. DO NOT POLLUTE THE ENVIRONMENT!

After spray application, take a thoroughly cleans- ing shower using plenty of water and soap, then change into clean clothes. Protective clothing and safety gear should also be cleaned after each use. IN CASE OF EXPOSURE TO DANGER- OUS CHEMICALS, seek a physician immedi- ately and be prepared to provide the label from the chemical container.

(Requires optional flow calibrator bottle, P/N 646901)

1. Hold the wand
	at the working
	height and spray
	a test pattern to
	measure the appli-
	cation band width.
2. Based on the band
	width, identify from the
	table below the walking
	distance required to calibrate
	the sprayer.
	Band width	1.6 ft	2.3 ft	3.3 ft	4.0 ft		5.0 ft
		0.5m	0.7m	1.0m	1.2m		1.5m
	Distance to walk	165 ft	120 ft	80 ft	70 ft		55 ft
		50.0m	35.7m	25.0m	20.8m
3. Attach the flow calibrator bottle to the wand:
	a. Remove the nozzle, cap and
	filter from the spray wand.					Wand
	b. Mount the flow calibrator
	cover to the spray wand.					Cover
	c. Reinstall the nozzle, filter					Filter
	and nozzle cap.
						Nozzle
	d. Screw the flow calibrator
	bottle into the cover.					Nozzle
4. Using the flow calibrator bottle:							Cap
	a. Operate the pump handle to					Calibrator
	maintain spray system pres-						Bottle

sure as you would when applying chemicals.

b. Hold the wand at your normal working position and spray into the bottle while walking the distance identified in step 2 above.

c. Place the bottle on a level surface and observe the liquid level visible through the side of the bottle. Match the liquid level to the l/acre (liter per acre) scale on the calibration bottle.

d. Multiply the l/acre (liter per acre) reading identified in step 4-c by .264 to determine your application coverage rate in gallons per acre.

e. Empty the bottle contents back into the sprayer tank.

NOTE:

For improved accuracy in calibrating your application coverage, repeat steps 4-a through 4-e and average the results.

Typical Nozzle Assemblies

Filter	Filter	Tip
	Swirl Core
Tip
	Disc
Cap	Cap	The spraying angle is
		changed by turning
		the tip
Flat Fan Nozzle	Cone Nozzle	Adjustable Cone
		Nozzle

No.		Description	Part Number	Qty.
	02	Strap Assembly	925198	1
	03	Strap 1800mm	901018	1
	04	Shoulder Protector SP-150	917477	1
	05	Shoulder Strap Buckle	502757	2
	06	Tank Lid Assembly	922550	1
	07	O-Ring, Tank Lid	8000778	1
	08	Diaphragm Valve (viton)	964270	1
	10	Cylinder Assembly	285262	1
	11	Piston Cup	285270	1
	12	Bushing	285288	2
	13	Cylinder Cap	285296	1
	14	Pumping Handle	N/A	1
	15	Pumping Handle Assembly	285312	1
	16	O-ring ORI-110	8000236	1
	17	Dip Tube With Hose	9012246	1
	18	Screw Cap S-20	942193	1
	19	Trigger	568972	1
	20	Trigger Valve Handle	909192	1
	21	Hose Ferrule	920470	1
	22	Trigger Valve Body	909283	1
	23	Trigger Valve Needle Assembly	105239	1
	24	Trigger Valve Cap With Seal	996058	1
	25	Trigger Valve Assembly	568782	1
	26	Cone Packing	909309	2
	27	Screw Cap	915744	2
	28	Tube	336263	1
	29	Elbow	635276	1
	30	Nozzle Filter	592139	1
	35	Ajustable Cone Nozzle (Red)	015024	1
	36	Extension Assembly	568873	1
	37	Spray Wand Assembly	568774	1
	38	Seal Kit (Optional)	927850	1

2 7