Shure 515SBGX specifications Furnished Accessories, Replacement Parts, Connections

Switch

Built-in, leaf-type, non-locking, push-to-talk

Shock Mount

Internal rubber vibration isolator

Cable

Highly durable cable with effective hum shielding, four conduc- tors (two shielded), plastic jacketed

Model 515SBGX: 1.8 m (70 in.)

Models 515SBG-18X and 515SBG-18XF: 1.3 m (51 in.) from gooseneck

Case

Silver finish die casting with black enamel diecast grille and stainless steel screen

Dimensions

See Figure 3

	6.5 in.
	16.5 cm
	51 in.
	120 cm
	0.85 in.
1.5 in.	2 cm
3.75 cm
	OVERALL DIMENSIONS
	FIGURE 3
Certification

The GREEN and WHITE cable leads are used to control an exter- nal relay or control circuit. Refer to the following table and to the wiring diagram in Figure 4.

	WIRE	FUNCTION	XLR	1/4 IN.
	COLOR		CONNECTOR	PHONE
INPUT TYPE				PLUG
	RED	AUDIO	PIN 2	TIP
UNBALANCED	BLACK	AUDIO GROUND	PIN 3	SLEEVE
	SHIELD	CHASSIS GROUND	PIN 1	SLEEVE
	RED	AUDIO +	PIN 2	TIP
BALANCED	BLACK	AUDIO -	PIN 3	RING
	SHIELD	CHASSIS GROUND	PIN 1	SLEEVE

DIRECTION TO ACTUATE

SWITCH

CASE GROUND

RED DOT GREEN

WHITE

BLUE

BLACK

Conforms to European Union directives, eligible to bear CE

marking; meets European Union EMC Immunity Requirements

CARTRIDGE

RED

(EN 55103).

Net Weight

515SBGX	380 g (13.5 oz)
515SBG-18X	900 g (31.8 oz)
515SBG-18XF	787 g (27.8 oz)

FURNISHED ACCESSORIES

1.27 mm (.050 in.) Hex Wrench	80A67
45.75 cm (18 in.)Gooseneck
(515SBG-18X, 515SBG-18XF only)	G18
Flange (515SBG-18X only)	A13HD
Flange (515SBG-18XF only)	A12

REPLACEMENT PARTS

Cartridge	R180
Grille Assembly	RK334G
Cable	70A4063
Gooseneck (515SBG-18X, 515SBG-18XF)	G18
Flange (515SBG-18X)	A13HD
Flange (515SBG-18XF)	A12
Windscreen	A85WS

CONNECTIONS

These low-impedance microphones are designed for connection to microphone inputs rated at 75 to 300 ohms. Using balanced-line low-impedance cables permits very long cable lengths without af- fecting response or level. The RED and BLACK cable leads are the microphone conductors for balanced-line connections; the shield is connected to the amplifier ground.

For unbalanced operation, connect the BLACK lead to the shield, and use the RED lead as the microphone conductor.

SHIELD

INTERNAL CONNECTIONS

FIGURE 4

MOUNTING THE 515SBG-18X AND 515SBG-18XF

Mount the 515SBG-18X or 515SBG-18XF as follows:

1.Thread the supplied hexnut all the way down on the mounting flange.

2.Thread the gooseneck tightly on the flange.

3.Back the hexnut up against the gooseneck, and use a wrench to tighten the nut firmly against the bottom of the gooseneck.

MOUNTING THE 515SBX ONTO A GOOSENECK

Mount the 515SBGX onto a gooseneck or fixed pipe with a 5/8 in-

27 thread as follows:

1.Unscrew the black end cap from the microphone.

2.Remove the thin metal washer and the metal spacer.

3.Re-install the washer by sliding it back onto the cable and up into the end of the microphone.

4.Slip the cable into the gooseneck or pipe and thread the microphone firmly to the mount.

For additional service or parts information, please contact Shure's Service department at 1-800-516-2525. Outside the United States, please contact your authorized Shure Service Center.

SHURE Incorporated http://www.shure.com United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Phone: 847-600-2000 U.S. Fax: 847-600-1212 Intl Fax: 847-600-6446 Europe, Middle East, Africa:

Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414 Asia, Pacific:

Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055

2