M O D E L A 1 0 0 A C A R R Y I N G H A N D L E A S S E M B L Y

The Shure Model A100A Carrying Handle Assembly provides a means for conveniently carrying the Shure Model SE30 Gated Compressor/Mixer. The Model A100A serves as a handle for carrying the SE30, as a cover for the front panel, and as a tilt stand for position- ing the SE30 at an angle for easy reading of the con- trols and meters. The A100A is easily switched from carrying handle use to tilt stand use simply by re- adjusting two knurled bolts which secure the Model A100A to the SE30. When in the tilt stand position, the SE30 rests on rubber feet mounted on the Model A100A. When in a carrying position, the SE30 may be rested on any flat surface and is then protected by the die cast corners on the rear of the case.

to mount the Model A100A on the Model SE30, proceed as follows:

1.Place the back (bottom) of the SE30 on a flat surface with the front controls facing up.

2.Position the Model A100A over the front of the SE30. The top of the screw slots on the sides of the Model A100A should align with the two tapped holes (C) on the sides of the SE30. See Figure 1, Carrying Position.

3.Screw the two knurled bolts supplied with the Model A100A fully clockwise into the two tapped holes (C) on each side of the SE30.

To position the Model A100A in tilt stand position, proceed as follows:

1.Loosen the knurled bolts at sides of Model A100A by turning them partially counterclockwise.

2.Lift the Model A100A away from the SE30 so that the knurled bolts pass through the bottom of screw slots.

3.Swing the Model A100A handle beneath the SE30 and tighten the knurled nuts (screw clockwise). See Figure 1 Position in Use.

CARRYING POSITION

TILT STAND POSITION

CARRYING HANDLE ASSEMBLY

FIGURE 1

Copyright 1979, Shure Brothers Inc 27A865 (SK)

MODEL A100B RACK PANEL

The Model A100B Rack Panel provides the Model SE30 with supports for rack mounting. To mount the Model A100B to the Model SE30, proceed as follows:

1.Unscrew the four rubber feet from the bottom of the SE30 to eliminate the obstruction of the rubber feet when sliding the SE30 into a rack panel.

2.Remove screws A and B (turn counterclockwise) from each side of the SE30. See Figure 2, Rack Panel.

3. Position the Model A100B brackets on the sides of the SE30; the three holes of the rack panels are to be aligned with the three tapped holes A, B and C on sides of SE30.

4. Replace screws A and B (turn fully clockwise) to fasten brackets to SE30.

5. Screw the ¼ inch bolts supplied with the Model A100B fully clockwise into the tapped holes at C.

OVERALL DIMENSIONS

RACK PANEL

FIGURE 2

Printed In U.S.A.

Page 29 Page 31
Page 30
Image 30
Shure SE30-2 service manual Carrying Handle Assembly
Page 29 Page 31

SE30, SE30-2 specifications

The Shure SE30-2 and SE30 in-ear monitors are premier audio devices designed for both audiophiles and professionals alike. Renowned for their exceptional sound quality and comfort, these models are essential for anyone serious about their audio experience.

One of the key features of the Shure SE30-2 and SE30 is their detailed sound reproduction. With a frequency response that spans from low bass to crisp highs, these monitors are engineered to deliver a balanced audio experience. The dual-driver configuration in the SE30-2 ensures that low, mid, and high frequencies are rendered with precision, allowing users to appreciate the nuances in their favorite tracks or during live performances.

Comfort is paramount in the design of the SE30 series. These in-ear monitors come with an ergonomic design and a variety of ear tip options, including foam and silicone tips, which help achieve a secure fit. This not only enhances comfort during extended use but also aids in passive noise isolation, allowing users to focus on their music without external distractions.

Shure has integrated innovative technologies into the SE30-2 and SE30 models, including a detachable cable system. This feature allows for easy replacement of worn cables and is particularly useful during live performances, where durability is crucial. The cables are also robust, with reinforced connectors that enhance longevity.

Moreover, the SE30 series is designed with versatility in mind. Whether you are using them in a studio setting, during live performances, or for casual listening, these monitors adapt to deliver optimal performance. The lightweight construction ensures that they are portable and suitable for on-the-go use, making them perfect companions for traveling musicians and audiophiles alike.

In terms of aesthetics, the Shure SE30-2 and SE30 sport a sleek, professional look, available in several color options. This not only appeals to the stylish user but also complements their refinement in sound.

In summary, the Shure SE30-2 and SE30 in-ear monitors present a compelling choice for those who seek high-fidelity audio in a comfortable and durable form factor. With attention to sound quality, comfort, user-friendly designs, and robust construction, these monitors stand out in a market filled with various audio options. Whether for professional use or personal enjoyment, the Shure SE30 series is sure to elevate any listening experience.
Top Page Image Contents