Shure specifications MODEL X100E, kFNNNEL, Phonograph Cartridge, ibZNEL, Stereo Dynetic@

222 HARTREY AVE.. EVANSTON. IL. 60204 U.S.A.

AREA CODE 3121866.2200 .CABLE SHUREMICRO

TWX: 910.231-0048 TELEX: 72.4381

THE PREMIER FAMILY OF STEREO SOUND REPRODUCERS

MODEL X100E

STEREO DYNETIC@

PHONOGRAPH CARTRIDGE

CARTRIDGE AND STYLI SPECIFICATIONS

N75EC	Brown	9.3 mV	20 to	within	20 dB	2 to 4	400 Hz - 26 cm/sec
10 X 18p			20.000	2 dB	at	grams	1,000 Hz - 37 cm/sec
(.OW4 X			Hz		1 kHz		10,000 Hz - 12 cm/sec
.0007 in.)							at 3 grams
Biradial
(Elliptical)				- - 1%
N75-3t	Dark	6.2 mV	20 to
64 microns	Green		20,000			to 3
(.0025 in.)			Hz			grams

Spher~cal

toptlonal 78 rpm Stylus: Set ampllfler to "MONO" or "A+ B "

*Output voltage5 glven for stereo cut record For MONO cut record, output vollagc at both left channel and rlght channel cartrldge terminals will be 71% o i ilgures above

'"lracking forces greater than maxlmum lnd~catedshould not be used

NET WEIGHT: 6.2 grdnls

INDUCTANCE: 720 millihenries

DC RESISTANCE: 630 ohms

OPTIMUM LOAD: 47,000 ohms resistance in parallel with 400 to 500 pico- farads total capacitance per channel. Load resistance can be up to 70,000 ohms with almost no audible change in frequency response. Total capaci- tance includes both tone arm wiring and amplifier input circuit.

FOUR-CHANNEL: This Stereo Dynetic@ cartridge is compatible with all four-channel matrix systems.

MONOPHONIC OPERATION: Set function switch on amplifier to "MONO" or "A+B." If amplliier is not equipped with this switch, connect left and right channels in parallel.

CONNECTIONS (see Figure 1): Right "hot" lead (usually red) to "R," right ground (usually green) to "RG " Left "hot" lead (usually white) to "L," left ground (usually blue) to "LC." If metal head is causing ground loop hum, remove the ground tab. The metallic cartridge shield is disconnected from the right channel ground by the removal of the ground tab.

CAUTION.	110 not make solder		kFNNNEL			7 ]/	/RIGHT
							CHANNkL
					r
ronncctlon	to	cartridge terminals	TEWINAL-	- 17L+L			TERMINAL
					-1		-GROUND TAB
STYLUS REPLACEMENT (see Fig-				I
ure 2) Grasp molded houslng of			ibZNEL				R I CHANNELTG
stylus and gently pull forward out							GROUNDTERMINAL
of cartridge		Insert replacement	,;I",,;				GROUNDEDTO CASE
stylus Into socket and press untll					FIGURE 1
housing mates wlth cartridge casr

MOUNTING [12.7 mm (112 in.) mounting centers]:

Mounting screws are provided.

1 . Remove stylus guard and stylus (see Stylus Replacement).

2.Connect leads to cartridge (see Figure 1).

3.Lay cartridge in shell and align mountlng holes on ~ i d eof car- tridge with holes or threads in shell. Follow turntable manu- facturer's instructionsto mount cartridge in tone arm or plug-in

shell.

4. Reinsert stylus (see Stylus Re-FIGURE 2 placement).

RECOMMENDED STYLUS CLEANING: Use a camel'shair brush (No. 2 size

or smaller), trlmmcd to approximately 6 mm (1/4 in.), dipped in alcohol or an alcohol-distilledwater solution. Commercial cleaning solutions may cause stylus damage or corrosion. Always brush stylus from back to front; never brush or wipe stylus from front to back or side to side.

TO PRESERVE STYLUS LIFE:

1. Follow turntable or tone arm instructions when adjusting antiskating force.

2 . D o not handle the tone arm while i t is i n operat~onsrrlce this may cause the arm to sweep across the record.

3.I f it is necessary to manually place the tone arm in the record groove while turntable is rotating, release it as soon as the stylus engages the record groove.

4.Correct improper set-down adjustment or malfunction of the turntable changing mechanism to prevent the stylus from striking the edge of the turntable or record. Do not stack more records than turntable manufac- turer recommends.

5.Take care to properly insert the stylus into the cartridge assembly and the cartridge and shell asscmbly into the tone arm receptacle.

6.Use proper vertical tracking force setting for each cartridge.

7.Do not use badly warped, cracked or imperfect records.

8.When dusting the turntable protect the stylus with the stylus guard.

SPECIAL NOTE: To maintain the original performance standards of your cartrldge, be certain that any replacement stylus you buy bears the follow- ing certification on the package: "This Stereo Dynetic@ stylus is precision manufactured by Shure Brothers Inc." AVOID INFERIOR IMITATIONS. THEY WILL SERIOUSLY DEGRADE THE PERFORMANCE OF YOUR CARTRIDGE. ALL GENUINE "DYNETICB" STYLI ARE MANUFACTURED BY SHURE BROTHERS INC. LOOK FOR THE NAME SHURE ON THE STYLUS GRIP. For more information on your Shure stylus, write for booklet: "A Visit to the Small World of a Stylus."

FULL ONE-YEAR WARRANTY: Shure Brothers lncorporated YShure"), 222 Hartrey Avenue, Evanston, Illinois 60204, warrants to the owner of this product that it will be free, in normal use, of any defects in workmanship and materials for a period of one year from date of purchase. You should retain proof of date o f purchase. Shure is not liable for any consequential damages. If this Shure product has any defects as described above, care- fully repack the unit and return it prepaid to:

Shure Brothers lncorporated Attention: Service Department 1501 West Shure Drive Arlington Heights, Illinois 60004

I f you are not in the United States, return the unit to your dealer or Authorized Service Center for repair. The unit will be repaired or replaced and returned to you promptly, and if it cannot be repaired or replaced, you may elect to receive a refund. This warranty does not include stylus wear.

PATENT NOTICE: Cartridge and stylus manufactured under one or more

of the following U.S. patents: 3,055,988, 3,077,521, 3,077,522, and 3,463,889.

Copyright 1980, Shure Brothers Inc.
27A1587 (TF)	Printed in U.S.A.