Technical data |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Installation of the wall holder | |||
Power adapter 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Mortal danger! | |
Input voltage: | 100 - 240 V~ |
|
| |||||||||||||||||
| 50/60 Hz | Ensure that there are no power cables or other con- | ||||||||||||||||||
| 200 mA | duits or pipes in the wall at the location where you | ||||||||||||||||||
Output voltage : |
|
|
|
|
|
|
| 10 V | intend to bore the holes for the wall holder 3. | |||||||||||
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
| ||||||||||||||
| 200 mA | It would be a potentially fatal risk to bore into a | ||||||||||||||||||
Protection class: | II | current carrying electric cable! | ||||||||||||||||||
Type designation: |
|
|
|
| ||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1. Place the barrel plug 5 of the power adapter 4 | |||
appliance |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| into the wall holder 3as shown in the diagramme. | ||
Input voltage: |
|
|
|
|
|
|
| 10 V |
| Secure the barrel plug 5 by turning it. | ||||||||||
|
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
| ||||||||||||||
| 200 mA |
|
|
|
| |||||||||||||||
Battery: | 7,2 V |
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
| |||||||||||||
Batteries |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Capacity: | 1300 mAh |
|
|
|
| |||||||||||||||
Batteries: | 6 x 1.2 V |
|
|
|
| |||||||||||||||
|
|
|
|
| ||||||||||||||||
| HR14/HRM 26/50 |
|
|
|
| |||||||||||||||
Information about the batteries
1.This hand vacuum cleaner is operated by recharge- able
Before using the cableless hand vacuum cleaner for the first time, the batteries must be charged for at least 24 hours.
2.The batteries reach their full capacity after a charging period of 24 hours. For care of the bat- teries we recommend the following: after the bat- teries are charged, remove the power adapter 4 from the mains power socket. Reconnect the power adapter 4 again with the mains power socket when the suction power of the appliance is noticeably weaker.
2.Select a suitable installation location for the wall holder 3: It should present no problem with taking the hand vacuum cleaner out of it and a mains power socket for the power adapter 4 must be accessible.
3.Bore two holes with a spacing of approx. 58mm. Use the wall holder 3 to mark the boreholes: this will ensure the spacing is correct. The bore- holes must be suitable for 5 mm wallplugs.
4.Insert the wallplugs into the boreholes and, using the screws, firmly screw the wall holder 3to the wall.
5.You can place the nozzles on the lateral acces- sories holder.
6.Connect the power adapter 4 to a mains power socket.
- 4 -
