Sima Products WX-200 Setting the Siren Mode, Battery Installation, Alert Mode Siren Mode

Upon selection of the warning level, press the SAVE button to save and exit to the ADD ALERTS prompt of the main menu list. To add another alert at this time, press the NEXT button to enter the ADD ALERTS menu and repeat steps 3-5. To return to normal operation press the MENU button. Note: if you exit the ADD ALERTS menu by pressing the MENU button, your changes will not be saved.

Setting the Siren Mode

The WX-150 allows you to block the siren from sounding on some warnings that are not relevant to your area. For example, a flood warning that may be issued in your county may not affect your location. You may not want the siren to sound for a flood warning

alert. Note: Some alerts, such as Tornado Warning, are not blockable.

Battery Installation

The WX-200 uses 4 AA batteries for back-up power. It can run on non-rechargeable alkaline, or rechargeable Nickel Cadmium (Ni-Cad) or Nickel Metal Hydride (NiMH) batteries. When the radio is operating on battery power, the green READY light will blink.

Use the slide switch located inside the battery compartment to select the battery type. (See Fig. 1) When alkaline batteries are installed, push the switch down to select “ALK” When using rechargeable batteries, push the switch up to select “CHG”. It is recommended that rechargeable batteries be replaced every three years.

DO NOT CHARGE ALKALINE BATTERIES!

ALERT MODE

SIREN MODE

Administrative Mess

OFF

To set the Siren Mode :

1.Press and hold the MENU button for 3 seconds. The radio will display the main menu list showing ALERT MODE.

2.Press the UP() button 3 times to scroll up through the main menu list to the SIREN MODE menu.

3.Press the NEXT button to enter the Siren Mode menu. The words ADMINISTRATIVE MESSAGE will scroll across the top of the screen. This is the first alert on the list of alerts that NOAA can broadcast. You have the option to turn the siren OFF to block this alert or ON to receive it . Note: Some alerts are not blockable. Use the Alert Table on Page 25 to help you select which alerts to block. Use the PREV and NEXT buttons to make your selection.

4.After setting the Siren Mode for this alert, use the UP/DOWN (/) buttons to scroll through the list of alerts, following the same sequence to set the SIren Mode for each alert desired.

Always set the battery select switch to “ALK” before installing alkaline batteries. Using the “CHG” setting with alkaline batteries may cause batteries to leak and present a a fire hazard.

To install or replace the batteries:

- Turn the unit upside down. Locate the battery compartment door tab (Fig. 2), press down on the door tab and lift the cover up to open

- Insert the batteries into the battery compartment.
		+
Be sure to follow the polarity markings. (Fig. 3)	CHG		-	+	-
- Set the battery charging switch to ALK for non-
rechargeable alkaline batteries. Set it to CHG for	ALK
NiCad rechargable batteries.
		-	+	-	+
- Replace the cover.
NOTES: Rechargeable batteries must be charged

Upon selecting of the Siren Mode for the desired alerts, press the SAVE button to save and exit to the SIREN MODE prompt of the main menu list. To set the SIREN MODE for additional alerts at this time, press the NEXT button to enter the SIREN MODE menu and repeat steps 3 and 4. To return to normal operation press the MENU button.

Note: if you exit the SIREN MODE menu by pressing the MENU button, your changes will not be saved.

22

for at least 24 hours before they are ready.
Rechargeable batteries provide approximately 15
to 20 hours of operation time. Non-rechargeable
alkaline batteries will provide over 50 hours of
operation time. To maintain maximum backup time, Fig.1	Fig. 2	Fig. 3
do not disconnect AC power supply from the unit
while in use. Remove the batteries
when the unit is not used for a prolonged
period of time.		11