Skylink® Wireless Keyless Entry |
|
for Garage Doors | Model 18KR |
|
|
1. INTRODUCTION |
|
|
|
|
|
2. INSTALLATION (CONT)
In this package, you will find a keyless entry transmitter with 3V lithium batteries, a garage door receiver, a red / black wire and screws.
1 pc 2.6 x 6 screw (included)
1 pc 2.6 x 12 screw (included)
1 pc 2.6 x 25 screw (included)
Garage Door | Red/Black Wire |
Receiver | Keyless Entry Transmitter |
| |
| (Batteries inside) |
2. INSTALLATION
The following instructions will show you how to install the receiver. After installing, the keyless entry transmitter (already programmed to the receiver) can be used to operate your garage door opener.
You need to locate 2 things inside your garage to install the receiver:
1)the
2)an electrical outlet, select an electrical outlet different from the one
already connected to the power cord of the garage door opener to reduce the chance of interference. The further distance between the receiver and the garage door opener, the less interference between 2 devices.
Note: The length of the red/black wire is 20ft, so the receiver must be plugged into an electrical outlet that is within 20ft of the wall mounted door control. If there is no electrical outlet within 20ft of the wall mounted door control, an extension cord can be used for temporary installation.
Wall Mounted | Remove power cord of garage | |
door opener before installation. | ||
Door Control | ||
| ||
Electrical |
| |
Outlet |
|
Unplug the power cord of your garage door opener WARNING before installation to ensure power is not connected.
1Remove the
| Existing |
| wires |
| Note: There should be another |
| pair of wires connected to the 2 |
| terminals already. Do not remove/ |
Red / | disconnect these existing wires. |
Black wire |
|
Note: If you see no screws mounting the wall mounted door control, the screws are probably underneath the front cover. Remove the front cover by pressing onto the tabs on top of the cover.
Remove front |
cover first |
2Plug in the connector end of the Red/Black wire to the 18R receiver. Note the orientation of the male & female connector.
3Plug the receiver into an electrical outlet inside the garage.
The red light on the receiver should be on after being plugged into an electrical outlet.
Existing wires connected to garage door opener. (Do not remove)
RECEIVER
RED/BLACK WIRE
Note: Alternative wiring options are available, the receiver can be connected directly to the opener’s motor. Please contact customer service for further information regarding alternative wiring options.
4
5Remove the battery isolator on the transmitter and enter the factory default PIN [0,0,0,0], [#], [1] you will hear 3 beeps indicating y ou have entered the correct PIN. The door will now open.
6You can now mount the transmitter on a
desired location. | (a) |
Lift up the cover and insert screw |
|
above the keypad in the slot provided (a). |
|
Remove the battery cover and insert |
|
the second screw in the lower slot (b). |
|
Tighten all screws. Replace the battery | (c) |
cover, insert and tighten screw (c). | (b) |
|
3.TROUBLE SHOOTING
Q:Door opener does not reac t after pressing the button on the transmitter.
A:- Ensure you hear 3 beeps from the keypad transmitter after entering the default PIN [0,0,0,0], [#], [1]. If you do not hear 3 beeps, that means the PIN you entered is incorrect.
-If the red light on the receiver flashes after entering the PIN on the transmitter, but the door opener does not respond, please ensure the red/black wire is successfully connected from the receiver to the wall mounted door control.
-Ensure the wires that are previously connected to the wall mounted door control are not loose.
-Ensure the keypad transmitter has been programmed to the receiver. Refer to section 4 how to program a keypad to the receiver.
4. PROGRAM A KEYPAD TO THE RECEIVER
The transmitter in this kit has been programmed to the receiver in the factory. You need to do the programming only when you add additional keypad transmitter to the receiver.
1Plug the receiver into an electrical socket.
2Press and hold the learn button at the left hand side of the receiver. The red LED on the receiver will flash.